FAQ |
Members List |
Social Groups |
Calendar |
Search |
Today's Posts |
#21
|
|||
|
|||
Quote:
__________________
Merry Christmas,Happy Halloween, God bless America, and my Mother and Father.If you don't like your freedoms,ignore them and they'll go away! |
#22
|
||||
|
||||
Builtit has purchased a starter.
Rebate level at 4%. |
#23
|
|||
|
|||
Robb, I may have interest in one as well. My car is a 67 GTO, factory H.O. four speed and I run the original H.O. manifolds, is your starter going to install with these along with the four speed. The factory unit is a pain in the rear end to install with the cast iron headers and bell housing. Although I have never had a hot start issue the installation is a pain in the rear end to the point that if I run into a hot start problem I might as well fix it now with one of your designs. Please provide additional details when you have a free moment. ThankYou. (PM sent to you as well on the same topic).
Tim john--- |
#24
|
||||
|
||||
i had 4 .015 shims under my stock starter....should i get the short gear and use no shims ? or should i use the old shims and standard gear and see what i get ?
__________________
1981 Trans Am project -YJ 400 stroked to 488 CID-74cc Eheads-10.95:1-Northwind Intake-Holley Terminator-TH400-Moser rear-Dougs Headers.... |
#25
|
||||
|
||||
Quote:
The use of the standard or short gear has nothing to do with the shims. The shims effect how tightly the pinion gear meshes with the ring gear. The standard and short gears effect how far the pinion gear is from the ring gear when the starter is at rest. There should be .06 to .21" clearance between the pinion gear and the ring gear with the starter at rest. If the gap is less than .06", the short gear will be needed. Due to stack up of tolerances on the engine, you must bolt up the starter to determine if the short gear is needed. About 75% of the time the standard gear will work. |
#26
|
||||
|
||||
Quote:
|
#27
|
||||
|
||||
My starter just arrived(that was quick!) looks good,Ill let you know how it works on my Firebird in a month or so.Thanks Rob.
__________________
Mark 1970 Lemans Convertible,462,6x-4, 234/242 cam.3.42 posi.12.55@109,4100 lbs...SOLD.... 1968 Firebird , 467 , KRE d-ports ,stock type suspension,3100lbs (1.30 60')(6.08 1/8)(113.43)different runs 9.59 @140.71 on E85 all motor 8.97@148.63 on 150 shot |
#28
|
||||
|
||||
Robb,
I may be in, my mini-starter may have taken a dump after 5 months. Waiting on confirmation from my brother. I ordered your kicka$$ fuel pump... it is a peice of work. I'll let you know. Jake
__________________
Saving the world... One country at a time. |
#29
|
||||
|
||||
Thanks Jake. Glad the pump is working well for you!
JJump59 and Elkhornaog7 have ordered starters. Rebate at 6%. |
#30
|
||||
|
||||
Where are we going? Higher!! I wanna see that rebate at 25% (no disrespect rob, i am sure the starter is worth every penny)!
__________________
Derek B. Current best: 11.97@110 1.65-60' !!! '74 ventura, (Fired july 14/06) '74 462 4-bolt (9.5-1), SCAT, Ross, T-II w/850DP (shaker455), TH350, Conti 10'' 3800, Supercomps, Magnaflow, 3'' Pypes, 3.73's, 28x13.5-15 ET streets. 1970 Beismeyer 17' flatbottom vdrive, 11.8:1 455P, ported heads, dual Qjet tunnel ram. |
#31
|
||||
|
||||
Just received my starter today......nicely engineered piece. Won't be installing for awhile, but looks like a quality starter. Thanks Robb.
|
#32
|
||||
|
||||
Robb, I just ordered a starter on your web site. I put my py username in the message to seller box at the end of the paypal payment form, is that the correct place to list it?
Bob
__________________
[SIGPIC][/SIGPIC |
#33
|
||||
|
||||
Quote:
Rebate at 7%. Sales of our starters (all of them, not just Pontiac) have far exceeded our estimates for the past two weeks and we are waiting on more electric motors from the manufacturer. It may be two or three weeks before we can ship more starters. Sorry for the delay and the poor planning on our part. I will extend the offer until midnite October 31st to make up for the delay. Starters can still be ordered now or wait until we have more in stock. Orders will be shipped in the order we receive them. Thanks everyone for your patience. |
#34
|
||||
|
||||
Robb, the delay is not a problem for me. Thanks.
Bob
__________________
[SIGPIC][/SIGPIC |
#35
|
||||
|
||||
i purchased one of these staters a few weeks ago. i was unaware of any rebate/t-shirt deal. starter works great! way better than the stock delco. i love that 360 clocking for the solenoid. i used the original shims. no more starter issues with the r/a manifolds. awesome.........
|
#36
|
||||
|
||||
do you have an estimated shipping date.....i am not sure i can wait that long....????
__________________
1981 Trans Am project -YJ 400 stroked to 488 CID-74cc Eheads-10.95:1-Northwind Intake-Holley Terminator-TH400-Moser rear-Dougs Headers.... |
#37
|
||||
|
||||
Motors should be here the end of this week. It will probably take a week to modify them and and assemble. So I would say a week and a half at best.
|
#38
|
||||
|
||||
i guess i will be waiting...robb i want to send a money order. do i send it to
RobbMc Performance Products 2960 Cameron Court Carson City, NV 89706 and make payable to ... RobbMc Performance Products ? can i just include a noe with my PY user name for the rebate ? steve
__________________
1981 Trans Am project -YJ 400 stroked to 488 CID-74cc Eheads-10.95:1-Northwind Intake-Holley Terminator-TH400-Moser rear-Dougs Headers.... |
#39
|
||||
|
||||
Quote:
__________________
Some Fear, Because if you've never been afraid- just a little. You're obviously not going as fast as you could be. |
#40
|
||||
|
||||
That would be fine Steve.
Oldblueponcho has purchased a starter. Rebate at 8%. |
Reply |
|
|