Home Menu

Menu


          
PY Online Forums - Bringing the Pontiac Hobby Together > Search Forums > Search Results
Showing results 1 to 16 of 16
Search took 0.02 seconds. Search: Posts Made By: edvisme
Forum: 70-73 Firebird & TA TECH 02-14-2014, 12:47 PM
Replies: 9
Views: 721
Posted By SD73
I'm pretty sure they're the same as the nuts that...

I'm pretty sure they're the same as the nuts that held the tail lights in and more than one manufacturer used them. I did an ebay search and came up with these, but you can check for yourself to see...
Forum: 70-73 Firebird & TA TECH 02-13-2014, 10:57 PM
Replies: 9
Views: 692
Posted By transam1972
I AM A ROCKER,TOO

352966 the holes I am thinking of are on the center part,underneath...like weep holes for a rocker panel...you can see one in the center photo

352967

352968
Forum: 70-73 Firebird & TA TECH 02-13-2014, 02:02 AM
Replies: 9
Views: 692
Posted By transam1972
DRAIN HOLES

they are there for a reason..put away that torch!!!...part of the flush and dry rocker system!!
Forum: THE LOBBY 01-15-2014, 01:00 PM
Replies: 83
Views: 4,515
Posted By fiedlerh
brakes = stops a car breaks = made in china ...

brakes = stops a car
breaks = made in china
ensure = to make certain
insure = so you can drive your car
past = it happened a while ago
passed = what you did to a Mopar
Forum: 70-73 Firebird & TA TECH 01-07-2014, 12:05 AM
Replies: 11
Views: 1,065
Posted By transam1972
disasemble/reassemble

whenever I see a Firebird apart on the floor..I say that's a better man than me...I don't even have the guts to take off my inner fenders!!..I left the doors on, had new quarters put on..took the...
Forum: 70-73 Firebird & TA TECH 01-06-2014, 10:51 PM
Replies: 11
Views: 1,065
Posted By 72TAMAN
edvisme even the factory that build those cars at...

edvisme even the factory that build those cars at problem lining up the sheet metal. I how you have the book Echoes of Norwood so go to page 200 and read the next few pages you will see what I'm...
Forum: 70-73 Firebird & TA TECH 01-06-2014, 05:39 PM
Replies: 11
Views: 1,065
Posted By 2manyT/A'S
Ok,so your rad support is mounted on the subframe...

Ok,so your rad support is mounted on the subframe then?

Mount your fenders loosely....2 bolts to the cowl & 2 to the top of rad support (each side)......loosen the core support to frame horn...
Forum: 70-73 Firebird & TA TECH 01-06-2014, 02:23 PM
Replies: 11
Views: 1,065
Posted By 3tas4me
You can measure what you have on the frame to...

You can measure what you have on the frame to make sure everything is square. The other measurements are going to depend on how you need to align the sheetmetal on your car. Align the doors first,...
Forum: 70-73 Firebird & TA TECH 01-05-2014, 07:55 PM
Replies: 29
Views: 2,001
Posted By Formulabruce
Cars and Forums of enthusiasts can be great...

Cars and Forums of enthusiasts can be great therapy when your down! Glad you have a nice Direction to go :)
Forum: 70-73 Firebird & TA TECH 01-05-2014, 07:36 PM
Replies: 29
Views: 2,001
Posted By FunctionalShaker
Good to hear you're still on your feet. May 2014...

Good to hear you're still on your feet. May 2014 be prosperous for you and everyone else on the forum.
Forum: 70-73 Firebird & TA TECH 01-05-2014, 06:13 PM
Replies: 29
Views: 2,001
Posted By transam1972
the 1972 Trans Am 455 H.Os new garaage

I want all you guys to know how important this PY forum is to me and how I really appreciate everyone...I lost my job on 11/10 and I really have not been myself...my fears of losing my possesions,...
Forum: The Body Shop TECH 01-01-2014, 06:16 PM
Replies: 7
Views: 513
Posted By Joel Koontz
Most 1K and 2K primer and most fillers are not...

Most 1K and 2K primer and most fillers are not waterproof or even water resistant.

Most Epoxy primer is "waterproof"(VERY water resistant-even topcoats are not totally waterproof)

I would...
Forum: 70-73 Firebird & TA TECH 12-17-2013, 01:47 AM
Replies: 1
Views: 921
Posted By Dens71TA
Service Manual specs out 85 ft. lbs. for the four...

Service Manual specs out 85 ft. lbs. for the four body to frame bolts and 35 ft. lbs. for the radiator support. New GM subframe bolts that I have purchased over a decade ago had a stripe of loctite...
Forum: 70-73 Firebird & TA TECH 12-17-2013, 01:15 AM
Replies: 1
Views: 921
Posted By 2manyT/A'S
Body mount bolt torque?

This would be for the 4 subframe to body mount bushings.....

Using the reproduction ones not urethane...

I'm thinking 80-100 ft.lbs with lightly oiled (cleaned) threads?
Forum: 70-73 Firebird & TA TECH 10-26-2013, 01:17 PM
Replies: 256
Views: 11,410
Posted By Tazzz2
For what it's worth American Auto Wire has a...

For what it's worth American Auto Wire has a awesome reputation of reproducing a headache free Top quality harness... While I don't personally do the electrical installs on my builds at 54,,, I have...
Forum: 70-73 Firebird & TA TECH 05-01-2012, 03:00 PM
Replies: 22
Views: 1,709
Posted By Formulajones
Here,,,,I'll help stir the pot some more since...

Here,,,,I'll help stir the pot some more since you guys aren't getting hostile enough yet :D

How about the 70 Formy's that were taken back to the dealer to have a spoiler installed? Should it...
Showing results 1 to 16 of 16

 
Forum Jump

All times are GMT -4. The time now is 03:33 PM.

 

About Us

The PY Online Forums is the largest online gathering of Pontiac enthusiasts anywhere in the world. Founded in 1991, it was also the first online forum for people to gather and talk about their Pontiacs. Since then, it has become the mecca of Pontiac technical data and knowledge that no other place can surpass.

 




Contact Us Home
Copyright © 2017