#1  
Old 10-14-2021, 09:52 AM
drewm drewm is offline
Senior Member
 
Join Date: Jul 2021
Location: Chester County, PA
Posts: 113
Default 6x-4's or 8s?

There are many threads on the positives and negatives of these heads, but all things being equal, which bare head would you prefer to start with for a 400 stroker build? The smaller chamber of the 4's or the larger 8's? Or are there other reasons you would choose one over the other?

Thanks
Drew

  #2  
Old 10-14-2021, 09:59 AM
PAUL K's Avatar
PAUL K PAUL K is online now
Ultimate Warrior
 
Join Date: Feb 2004
Location: Sugar Grove IL USA
Posts: 6,280
Default

First priority should be to get the compression ratio were you want it.

After that the -4 would be a better performance head but not by much. It offers slightly better port shape and a smaller chamber.

__________________
Go fast, see Elvis!
www.facebook.com/PaulKnippensMuscleMotors
The Following User Says Thank You to PAUL K For This Useful Post:
  #3  
Old 10-14-2021, 10:13 AM
drewm drewm is offline
Senior Member
 
Join Date: Jul 2021
Location: Chester County, PA
Posts: 113
Default

For sake of discussion, this is for a street car running pump gas.

  #4  
Old 10-14-2021, 10:26 AM
PunchT37's Avatar
PunchT37 PunchT37 is offline
Ultimate Warrior
 
Join Date: Dec 2002
Location: Lafayette,LA
Posts: 3,242
Default

#4`s. Use the smallest chamber then, dish the piston, if necessary to get your static compression. The smaller chamber head has a longer "short turn" and it unshrouds the valves for better breathing.

The Following User Says Thank You to PunchT37 For This Useful Post:
  #5  
Old 10-14-2021, 10:40 AM
Mike S's Avatar
Mike S Mike S is offline
Ultimate Warrior
 
Join Date: Dec 1999
Location: Vineland,N.J.
Posts: 1,513
Default

I have 6x-8 on my street car. Ported them at home. I shaved the heads down to get 90cc chambers. This was over 20 years ago but I believe they where shaved .060 and intake side was .030.
The car has been 11.8/113 at 3900lbs.

The Following User Says Thank You to Mike S For This Useful Post:
  #6  
Old 10-14-2021, 11:33 AM
steve25's Avatar
steve25 steve25 is online now
Ultimate Warrior
 
Join Date: May 2008
Location: Westchester NY
Posts: 14,631
Default

My findings from porting well over 18 sets of of 6X heads over the years with a spread of about 70% of them being -4 and the rest -8 is that the port shapes are the same within casting tolerances.

It's the 6H casting that they had to resort to making the chamber deeper to get up to 124 or so CCs where in the port shapes / depths where shortened.

Due to where the chambers where carved out more in the -8 heads they are a little less shrouded then the -4s, but this added air flow only shows up when the Intake side of the heads are ported a great amount and valve lifts above .600" are used.

All low compression heads that do not use the RA4 type chamber from 71 and up if using 2.11"valves and ported to flow 230 cfm and up could make good use of having the chamber unshrouded as in this photo.
Attached Thumbnails
Click image for larger version

Name:	IMG_0979.jpg
Views:	192
Size:	72.3 KB
ID:	575138  

__________________
Wernher Von Braun warned before his retirement from NASA back in 1972, that the next world war would be against the ETs!
And he was not talking about 1/8 or 1/4 mile ETs!

1) 1940s 100% silver 4 cup tea server set.

Two dry rotted 14 x 10 Micky Thompson slicks.

1) un-mailed in gift coupon from a 1972 box of corn flakes.
Two pairs of brown leather flip flops, never seen more then 2 mph.

Education is what your left with once you forget things!

Last edited by steve25; 10-14-2021 at 11:41 AM.
  #7  
Old 10-14-2021, 12:04 PM
NeighborsComplaint's Avatar
NeighborsComplaint NeighborsComplaint is offline
Ultimate Warrior
 
Join Date: Aug 2009
Location: Elgin
Posts: 2,468
Default

On a 400 the 6x4 would be preferred just based on compression ratio. There really is no significant flow advantage to any of those low compression Dport heads, just chamber size differences. The 6x and 96 are considered top of the heap though. In Pete McCarthy's article "Ultimate Head" published in HPP, he found a set of 5cs that were an anomaly in terms of flow superior to the 6x.

6x8 flows better than 6x4 if you plan to install 1.77" exhaust valves due to less valve shrouding in the larger combustion chamber but you would have to mill them to reduce the chamber volume for your 400.

__________________
Triple Black 1971 GTO

Last edited by NeighborsComplaint; 10-14-2021 at 12:10 PM.
  #8  
Old 10-14-2021, 12:10 PM
drewm drewm is offline
Senior Member
 
Join Date: Jul 2021
Location: Chester County, PA
Posts: 113
Default

So, basically if I am looking for a set of heads to work with a stroked 400 (461), and I have a set of 4's and a set of 8's available, I am gathering that the best initial choice would be the 4's due to CC size? No other advantages or disadvantages?

  #9  
Old 10-14-2021, 12:23 PM
steve25's Avatar
steve25 steve25 is online now
Ultimate Warrior
 
Join Date: May 2008
Location: Westchester NY
Posts: 14,631
Default

Run the -4 heads and get dished Pistons to achieve your desired compression ratio.
I find no flow advantage on my flow bench to the -4 chamber shape or the -8 chamber shape in regards to either head running the stock 1.66" or the larger 1.77" Exh valve .

The layed back area of chamber enlargment in the - 8 head is more than 1/2" above the Exh valve seat and has no impact on Exh flow!

__________________
Wernher Von Braun warned before his retirement from NASA back in 1972, that the next world war would be against the ETs!
And he was not talking about 1/8 or 1/4 mile ETs!

1) 1940s 100% silver 4 cup tea server set.

Two dry rotted 14 x 10 Micky Thompson slicks.

1) un-mailed in gift coupon from a 1972 box of corn flakes.
Two pairs of brown leather flip flops, never seen more then 2 mph.

Education is what your left with once you forget things!
The Following User Says Thank You to steve25 For This Useful Post:
  #10  
Old 10-14-2021, 01:17 PM
dmac dmac is offline
Ultimate Warrior
 
Join Date: Oct 2007
Posts: 1,229
Default

For a street car running pump gas, getting the CR right should top concerns over flow. I doubt that performance at street RPMs will vary much if at all, but 'street' use can mean different things to different people. And if you already have your pistons, you may have less of a choice, and need to pick based off compression ratio you want to be able to use pump gas, which can also vary. My pump gas can be from 86 to 91 octane, which is enough difference to matter. If you are close to the edge and run low and have limited gas available. I would rather use 91 octane in a car built to use 86 vs using 86 in a can designed to use 91.

The Following User Says Thank You to dmac For This Useful Post:
  #11  
Old 10-14-2021, 02:18 PM
'ol Pinion head 'ol Pinion head is offline
Ultimate Warrior
 
Join Date: Apr 2000
Location: INJUN Territory, Red State Merica!
Posts: 9,564
Default

Quote:
Originally Posted by drewm View Post
There are many threads on the positives and negatives of these heads, but all things being equal, which bare head would you prefer to start with for a 400 stroker build? The smaller chamber of the 4's or the larger 8's? Or are there other reasons you would choose one over the other?

Thanks
Drew
Drew, To answer your direct question, in a PUMP GAS (street) cast iron 6x type Stroker build in a 400 block, if the plan was to go with a 4.00" stroke crank, that would allow slightly milled 6X-4's & an undished piston. That noted, if you have a pair of 6X-8's or 5C-7 or 5C-8 heads (with near 100cc chambers), they would be better suited to 4.25" stroke build in a 400 block.

Procuring 6X-4's,mthey will command more $$$ & are typically harder to find than the 100cc chamber '75-78 400 heads. Through the 90's & early 00's, I kept a major Pontiac crate engine builder in 400 6x-4 longblocks. In doing so, I routinely pulled 6X-4's & mated them with '67-early '75 400 shortblocks. Also pulled all the W72 longblocks I could for future sales. In several yards I was literally chunking 100 cc smog era Pontiac heads in the open trunks of cars. Only if I was long on 455 short blocks would I need the few 6x-8's that came in usually on partscar 400's.

__________________
Buzzards gotta eat... same as worms.
The Following User Says Thank You to 'ol Pinion head For This Useful Post:
  #12  
Old 10-14-2021, 02:21 PM
drewm drewm is offline
Senior Member
 
Join Date: Jul 2021
Location: Chester County, PA
Posts: 113
Default

Quote:
Originally Posted by 'ol Pinion head View Post
Drew, To answer your direct question, in a PUMP GAS (street) cast iron 6x type Stroker build in a 400 block, if the plan was to go with a 4.00" stroke crank, that would allow slightly milled 6X-4's & an undished piston. That noted, if you have a pair of 6X-8's or 5C-7 or 5C-8 heads (with near 100cc chambers), they would be better suited to 4.25" stroke build in a 400 block.
I have the time to find either 4's or 8's, so I just wondered which would be a better starting point. Looks like most of Butlers stroker kits are 4.25 cranks so thats likely where I would end up.

  #13  
Old 10-14-2021, 02:52 PM
ta man ta man is offline
Ultimate Warrior
 
Join Date: Apr 2006
Location: Clinton,Ontario,Canada
Posts: 5,348
Default

Quote:
Originally Posted by drewm View Post
I have the time to find either 4's or 8's, so I just wondered which would be a better starting point. Looks like most of Butlers stroker kits are 4.25 cranks so thats likely where I would end up.
There may be a few ported cast heads for sale soon going by a few of the threads.

__________________

466 Mike Voycey shortblock, 310cfm SD KRE heads, SD "OF 2.0 cam", torker 2
373 gears 3200 Continental Convertor
best et 10.679/127.5/1.533 60ft
308 gears best et 10.76/125.64/1.5471
  #14  
Old 10-14-2021, 03:52 PM
PAUL K's Avatar
PAUL K PAUL K is online now
Ultimate Warrior
 
Join Date: Feb 2004
Location: Sugar Grove IL USA
Posts: 6,280
Default

It would be silly to spend money on a dished piston so you can use the -4 head. It would also be silly to spend money milling -8 heads if the -4's will give you the targeted compression ratio.

That is why your desired compression ratio should be your primary concern.... See post #2

__________________
Go fast, see Elvis!
www.facebook.com/PaulKnippensMuscleMotors
  #15  
Old 10-14-2021, 04:20 PM
Skip Fix's Avatar
Skip Fix Skip Fix is offline
Ultimate Warrior
 
Join Date: Dec 1999
Location: Katy,TX USA
Posts: 20,541
Default

Quote:
Originally Posted by PunchT37 View Post
#4`s. Use the smallest chamber then, dish the piston, if necessary to get your static compression. The smaller chamber head has a longer "short turn" and it unshrouds the valves for better breathing.
The only difference I noted was the -4 chamber is smaller diameter not a different depth. Mine were 93cc untouched. I smoothed the chamber ridge and milled them 0.050 and they were still 93cc. My 78's original -8s are 97.5cc.

I have a set of ported -8s they smoothed the ridge on that go 105cc.

__________________
Skip Fix
1978 Trans Am original owner 10.99 @ 124 pump gas 455 E heads, NO Bird ever!
1981 Black SE Trans Am stockish 6X 400ci, turbo 301 on a stand
1965 GTO 4 barrel 3 speed project
2004 GTO Pulse Red stock motor computer tune 13.43@103.4
1964 Impala SS 409/470ci 600 HP stroker project
1979 Camaro IAII Edelbrock head 500" 695 HP 10.33@132 3595lbs
  #16  
Old 10-14-2021, 04:45 PM
drewm drewm is offline
Senior Member
 
Join Date: Jul 2021
Location: Chester County, PA
Posts: 113
Default

This has been a fun thread for me. However I can't say that I am any less confused. Maybe if I posed the question another way...you walk into a garage, and the guy has a set of 8's and a set of 4's laying there. Which ones do you take home with you? Maybe there is no right answer?

  #17  
Old 10-14-2021, 04:49 PM
PAUL K's Avatar
PAUL K PAUL K is online now
Ultimate Warrior
 
Join Date: Feb 2004
Location: Sugar Grove IL USA
Posts: 6,280
Default

Quote:
Originally Posted by drewm View Post
This has been a fun thread for me. However I can't say that I am any less confused. Maybe if I posed the question another way...you walk into a garage, and the guy has a set of 8's and a set of 4's laying there. Which ones do you take home with you? Maybe there is no right answer?
Which one gets you closest to your desired compression ratio?

__________________
Go fast, see Elvis!
www.facebook.com/PaulKnippensMuscleMotors
  #18  
Old 10-14-2021, 04:59 PM
drewm drewm is offline
Senior Member
 
Join Date: Jul 2021
Location: Chester County, PA
Posts: 113
Default

Quote:
Originally Posted by PAUL K View Post
Which one gets you closest to your desired compression ratio?
Right now, I have a virgin 400 block sitting in my garage. I suppose I am shooting for about 9.5 CR. I realize that the block and heads will need to be machined and built to obtain a good pump gas CR. I just dont know which heads would get me there more efficiently. I am seeing just as many strokers built with 8's as with 4's, so maybe the answer is...it depends?

  #19  
Old 10-14-2021, 05:51 PM
steve25's Avatar
steve25 steve25 is online now
Ultimate Warrior
 
Join Date: May 2008
Location: Westchester NY
Posts: 14,631
Default

If your staying with the stock 3.750” stroke of the 400 then the -4s are the only way to go if your working only with 6X castings.

If your contemplating stuffing in a longer stroke crank to gain more cid then there may come a time where the -8s make more sense to avoid having to go for a dished piston.
That’s the bottom line.

__________________
Wernher Von Braun warned before his retirement from NASA back in 1972, that the next world war would be against the ETs!
And he was not talking about 1/8 or 1/4 mile ETs!

1) 1940s 100% silver 4 cup tea server set.

Two dry rotted 14 x 10 Micky Thompson slicks.

1) un-mailed in gift coupon from a 1972 box of corn flakes.
Two pairs of brown leather flip flops, never seen more then 2 mph.

Education is what your left with once you forget things!
  #20  
Old 10-14-2021, 06:32 PM
drewm drewm is offline
Senior Member
 
Join Date: Jul 2021
Location: Chester County, PA
Posts: 113
Default

Quote:
Originally Posted by steve25 View Post
If your staying with the stock 3.750” stroke of the 400 then the -4s are the only way to go if your working only with 6X castings.

If your contemplating stuffing in a longer stroke crank to gain more cid then there may come a time where the -8s make more sense to avoid having to go for a dished piston.
That’s the bottom line.
Definitely the longer stroke.

Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -4. The time now is 08:22 AM.

 

About Us

The PY Online Forums is the largest online gathering of Pontiac enthusiasts anywhere in the world. Founded in 1991, it was also the first online forum for people to gather and talk about their Pontiacs. Since then, it has become the mecca of Pontiac technical data and knowledge that no other place can surpass.

 




Copyright © 2017