FAQ |
Members List |
Social Groups |
Calendar |
Search |
Today's Posts |
#1
|
||||
|
||||
DOES ANY ONE KNOW IF A 70 GTO HAS A TOP PLATE THAT BOLTS ON OVER THE CORE SUPPORT?? OR WAS THIS ONLY FOUND ON A LeMANS ??? I THINK THERE SOULD BE A FILLER BETWEEN THE CORE SUPPORT AND THE NOSE..
JIM |
#2
|
||||
|
||||
DOES ANY ONE KNOW IF A 70 GTO HAS A TOP PLATE THAT BOLTS ON OVER THE CORE SUPPORT?? OR WAS THIS ONLY FOUND ON A LeMANS ??? I THINK THERE SOULD BE A FILLER BETWEEN THE CORE SUPPORT AND THE NOSE..
JIM |
#3
|
|||
|
|||
Yes there is a filler panel that bolts to the rad support you can buy a repo
|
#4
|
||||
|
||||
Just to clarify, the 70 GTO top plate is just a black plastic cover, not a steel tray like on the lemans. There are fiberglass and plastic repops.
GR-RRR!
__________________
1970 GTO 458 CID .040 over 4 Bolt 428 Block, Forged Eagle 455 Crank, 295 CFM SD KRE D-Ports, SD Old Faithful HR Cam + Comp HR Lifters, PPR Maxx-lite rods, Racetec pistons, PRW 1.65 SS Rockers, 900CFM Holley HP TBI, Performer RPM, Hooker Super Comps, 3" X-Pipe into 2.5" mufflers/tailpipes, 2.75 1st TH400, Continental 13" Converter, 8.5" 3.08 Posi. Everything installed, fired up and tuning has begun! |
#5
|
|||
|
|||
I bought a plastic one from PY and the fit was great.
Trying to find an original one in good usable condition will be extremely tough. |
#6
|
|||
|
|||
Scott Nimons, was the filler you bought like your original? When I looked for one everybody was selling the same one, which had a textured pattern, and it didn't look like my original.
|
#7
|
|||
|
|||
Does any one have a GTO that came from the factory without the filler panel? Mine and another very original 70 never had one. They are both non air cars and have close build dates 4/70
|
#8
|
||||
|
||||
I believe the plastic repo's to be very close to original. I have heard the top is correct looking but the underside is incorrectly grained, but you would never see that once installed. Not only that but the plastic ones are cheaper than the incorrect fiberglass ones. This is just what I have read though.
GR-RRR!
__________________
1970 GTO 458 CID .040 over 4 Bolt 428 Block, Forged Eagle 455 Crank, 295 CFM SD KRE D-Ports, SD Old Faithful HR Cam + Comp HR Lifters, PPR Maxx-lite rods, Racetec pistons, PRW 1.65 SS Rockers, 900CFM Holley HP TBI, Performer RPM, Hooker Super Comps, 3" X-Pipe into 2.5" mufflers/tailpipes, 2.75 1st TH400, Continental 13" Converter, 8.5" 3.08 Posi. Everything installed, fired up and tuning has begun! |
#9
|
|||
|
|||
My 70 doesn't have one either. it was built 1/70.
|
#10
|
|||
|
|||
SlowGTO,
What 428 said. I think it looks good. It really polishes off the top of the radiator support, hiding all the bolts and closing the gap between the support and the nose. I can get a pic if you'd like. |
Reply |
|
|