FAQ |
Members List |
Social Groups |
Calendar |
Search |
Today's Posts |
#21
|
|||
|
|||
I ordered 1.7 from Jegs. Calling Crower to double check it got through to them today.
The other fellow that ordered them got 1.65. The promo code ends soon from Jegs. |
#22
|
||||
|
||||
I run 1.6
__________________
1969 LeMans..Liberty Blue 2001 WS6..Sunset Orange 1973 Pro Street Firebird..Lucerne Blue |
#23
|
||||
|
||||
Quote:
Watched your videos, nice runs with the car. Have you ordered any pistons yet? I have a new set of CP Carillo here if interested. send me a pm. Thanks
__________________
68 Firebird. IA2 block, 505 cu in, SD Performance E-head, Solid roller 3600 weight. Reid TH400 4:11 gear. 29" slick. Best so far 9.95@134 mph. 1.43 60 ft. 76 Trans am, TKX .81 o/d, 3.73 Moser rearend, 468 with KRE D-ports, Doug headers, 3" Exh. |
#24
|
||||
|
||||
I ordered 1.7 I&E, but haven’t received them yet. Has anyone receiver theirs yet?
Once I get the Crower shaft rockers I’ll mount them up to verify they will fit / work on my heads. My heads are currently at the machine shop to have the water jackets leak checked. When I pick them up next week, I’ll drop off my Crower Billet crankshaft and have checked for possible defects, since it’s a used crank. I’ll be ordering a cam next, and no I haven’t ordered pistons yet. Chuckie what size bore are the pistons you have for sale? Do you have a link to the pistons? Thanks.
__________________
1969 Firebird, Tx3-455/468 machined by CVMS E-heads by Dave Wilcox/Comp Cams 300B-6 flat solid 850DP on E-85 by Eric Niefert/T2 1" plastic spacer T-400/PTC 4000/390's/30x9 Hoosier radial slicks,#3400 1.38 60' 6.32 @ 108 MPH at Northeast Dragway NC 5/23/15 (9th pass on new engine) https://m.youtube.com/watch?v=ePCu2v...ature=youtu.be 1.37 60' 6.26 @ 109 half track, 9.86 @ 136 1/4 mile, #3350 11/26/16 at Richmond Dragway (125th pass on new engine) |
#25
|
||||
|
||||
Hi: Sent you a PM. Here is a link. Price is negotiable. Thanks. https://forums.maxperformanceinc.com...22#post6175422
__________________
68 Firebird. IA2 block, 505 cu in, SD Performance E-head, Solid roller 3600 weight. Reid TH400 4:11 gear. 29" slick. Best so far 9.95@134 mph. 1.43 60 ft. 76 Trans am, TKX .81 o/d, 3.73 Moser rearend, 468 with KRE D-ports, Doug headers, 3" Exh. |
#26
|
|||
|
|||
My Crower shaft rockers showed up, very nice. I got them for 1537 $ but had to go through h#!! to get it. Jegs did not list the 74169F shaft rockers for the KRE head but did list the 74163F for 1639$ so with the 100$ promo code about 1540$ right ?
They did put the KRE shaft rockers on their site BUT it was 100$ more at around 1740$ and still is. When I went to buy I did not like that they put basically the same rocker, costs them the same as the E head shaft for 100$ more. I was trying to get the same price for me and any others that wanted to buy them. After lots of phone calls to sales and the sales person boss I got my price, but only me. Was told I was not getting any of my "buddies" at the same price. These jerks acted like they were doing me a favor so what they did was jack up the price of the 74163F E head shaft rocker to the same price as the KRE rocker so I could not b!t#h I guess. Summits sells both for 1740$ or so and takes Jegs promo code so you can always buy from them. BUT, there is one more good deal on Jegs so someone might want to take advantage of it before they jack up the price on that too. Its the "wide port" version of these with optional offfset. So if someone is looking for a nice set of Crower Endura SS shaft rockers for a wide port E head or KRE High Port head 1640 $ dropped down to 1540 $ with promo code is a good deal. https://www.jegs.com/i/Crower/258/74165/10002/-1 Considering T&D aluminum shaft rockers are 1900$ and 20 weeks out and still not as good as the Crowers 1540 $ is a good deal. And T&D charges another 1000 $ on top of that for steel rockers. At that point might as well buck up and buy Jessle. |
#27
|
||||
|
||||
Call and order them through Kauffman. They are at a better price and they have them drop shipped from Crower. Support the Pontiac guy’s keeping us in the game.
|
#28
|
||||
|
||||
That's what I did, had them in less than a week.
__________________
1969 LeMans..Liberty Blue 2001 WS6..Sunset Orange 1973 Pro Street Firebird..Lucerne Blue |
#29
|
|||
|
|||
What was KRE selling them for ? If he can do better than 1540$ that would be something for sure.
|
#30
|
|||
|
|||
I'm at .062 with .903 bushing type Crower lifters. Will see how it goes. Installing that engine soon.
__________________
Be carefull of the feet you step on today.They may be attached to the a$$ you kiss tomorrow. |
#31
|
||||
|
||||
Dragncar do you know the intake offset measurement for the Crower rockers for the wideport heads? I believe T&D list it as .450 and .700.
__________________
Todd Sedlmeier Who ever thought pinewood derby cars would lead to this! October 2004 HPP Shootout participate http://www.highperformancepontiac.co...out/index.html 86 Grand Prix 535 High Port 8.93 @ 153 65 GTO 433 High Port 12.04 @ 113 |
#32
|
|||
|
|||
Quote:
The 74165 are custom so I believe they are whatever you need. The way I understand it the .400 offset are for E heads without pushrod tubes welded or deleted. The .700 offset are for the big time wide ports. The T&D shafts I have say 1.7 on the exh rocker and 1.8 on the intake rocker. Not sure exactly what that means since the numbers are so close. The offset on the Jessle .903 lifters look to be about as far as you can move them. |
The Following User Says Thank You to Dragncar For This Useful Post: | ||
#33
|
||||
|
||||
Quote:
The 1.7 & 1.8 usually refer to the rocker arm ratio. |
#34
|
||||
|
||||
Geez
__________________
1969 carousel red firebird 455, richmond 5 speed 1964 540 gto 1971 lemans sport convertible 1972 Maverick under slow construction |
The Following User Says Thank You to mysticmissle For This Useful Post: | ||
#35
|
||||
|
||||
|
#36
|
|||
|
|||
I had not pulled them out of the box in years, in a hurry, made a post and went to work.
I thought the whole set was 1.8. Nice set of rockers with 4 extra. |
#37
|
|||
|
|||
|
#38
|
||||
|
||||
Well now you know what the 1.8/1.7 means.... Happy I could help.
|
#39
|
|||
|
|||
Yeah Paul.
I made the post and was on my way to work 5 minutes later when I realized my brain fart. Nothing I could do about it, could not delete it, edit it in time. I know how it looks. In a hurry, people asking me questions, lot on my mind. Life goes on. Lot bigger thing going on in my life at the moment, good things. I wanted to answer RA462 quickly because he is cool, try it sometime. I have 4 sets of roller rockers and 2 sets of shafts and most of them say what they are right on top. For some reason I was thinking the Jessle lifters had their offset stamped on them thats why I opened up the box. Glad I did, wanted to check them for rust. They are all good, had a NIB set rust on me before. |
#40
|
|||
|
|||
Here is the Crower Endura shaft rockers with optional offset.
https://www.jegs.com/i/Crower/258/74165/10002/-1 Promo code gets them down to 1540 $ |
Reply |
|
|