FAQ |
Members List |
Social Groups |
Calendar |
Search |
Today's Posts |
#1
|
|||
|
|||
Thought some of you might find this picture useful or at least interesting
This is a 16 head I cut in half with a hack saw to learn from for porting purposes way back in the 80s. I got lucky doing it with a standard size hacksaw and had to cut halfway from each side hoping they intersected. Got lucky with the guide mostly intact and the intake valve can be held in place for valve train mockups, and misc visualations.
|
The Following 2 Users Say Thank You to RBAILEY For This Useful Post: | ||
#2
|
||||
|
||||
That must of been some arm work out!
Did you do it all in one shot? Here’s two shot’s of a ported 290 cfm 16 casting, but the earlier one with the air injection boss still part of the casting. You see how far I ground into the roof and exposed a lot of the rocker stud hole. Thanks for saving the photo and posting it!
__________________
I do stuff for reasons. |
The Following User Says Thank You to 25stevem For This Useful Post: | ||
#3
|
|||
|
|||
That certainly shows how much metal you can take out of that troublesome inner bend.
|
#4
|
|||
|
|||
Quote:
I cut the head in half in one day at work using my breaks and lunch. So it took me a little less than an hour of hand hack sawing. The head I cut in half was being ported but got a hole in it in the bowl close to where it meets the guide at top of bowl; hitting the water jacket. You can see in the picture that is the thinnest area from that cross-sectional view. It wasn't really fixable so I cut the head up to learn from it and then found a set of small chamber 48s off a 350 HO (64cc chambers) and ported them. I finally got a set of Kauffman HighPorts so my 48s are now retired waiting for a backup engine build. Or if someone wants to buy them for the right price I might be able to break my attachment to them. Last edited by RBAILEY; 08-16-2022 at 03:21 AM. |
#5
|
||||
|
||||
Only about a hour, that's surprising!
These 16 heads took a 455 in a early Bird that was 3450 with driver into the low 10.20s I had custom 2.14" valves made up so I could run 45 degree seats and not sink the valve, also by doing that was able to get most of the upper part of the valve bowl quite big as you can see in the one photo. This allowed me to get a stout 155 cfm@ .200" lift which really helped the VE numbers.
__________________
I do stuff for reasons. Last edited by 25stevem; 08-16-2022 at 06:07 AM. |
#6
|
||||
|
||||
I have one of those cut-apart #16 cast iron heads on a shelf in my basement.
At least 25 years old. Tom V.
__________________
"Engineers do stuff for reasons" Tom Vaught Despite small distractions, there are those who will go Forward, Learning, Sharing Knowledge, Doing what they can to help others move forward. |
#7
|
|||
|
|||
Quote:
|
#8
|
||||
|
||||
Before I give you my answer I need to ask where in the intake runner are you considering the pinch point to be your asking about?
For me and a whole big bunch of other folks who port heads, it’s the area of the smallest amount of square inches.
__________________
I do stuff for reasons. |
#9
|
||||
|
||||
Tom, might you also have it cut apart in a way that exposes the intake port side of one of the center exh ports?
__________________
I do stuff for reasons. |
#10
|
|||
|
|||
the push rod bulge. im considering a gasket match 1233 gasket. as you can tell im a novice at porting. is there a specific dimension i should shoot for? those pics. helped me alot. thanks for the response and your help.
|
#11
|
||||
|
||||
If you want a head cut up, I have a 900lb, 10x18 Johnson bandsaw that would be great for this purpose. Built in 1946, no less - like a few of you old bastards.
__________________
Clutch Guys Matter _______________________________________ 53 Studebaker, 400P/th400/9" 64 F-85 72 4-4-2 Mondello's VO Twister II 84 Hurst/Olds #2449 87 Cutlass Salon 54 Olds 88 sedan |
#12
|
||||
|
||||
Let me first say that unless your intake is already matched to the 1233 then don’t bother!
A D port head can be reworked to flow 250 cfm before you need the added area of the 1233 gasket. After you do the gasket match on the common wall side of the port then You can safely go to a with of 1.064” at the apex. When grinding you want to try and keep the out bound side of the bulge a sharp edge / lip verticaly. This will help to keep the fuel in the air mass atomized like it should be. Opening up this pinch area depending on how much valve lift your running( and also if the rest of the intake runner) has been ported might only pick you up 2 to 5 cfm, but the main improvement will be your motors power band will be wider due to the air mass not having to contract and then expanded once again. If you go to post #2 here and click on my second photo you can double expand it to see that I ground back right to the .030” wall 1/2” OD brass tube . If your careful you should be able to come within .040” of that.
__________________
I do stuff for reasons. Last edited by 25stevem; 08-17-2022 at 02:18 PM. |
The Following User Says Thank You to 25stevem For This Useful Post: | ||
#13
|
||||
|
||||
My Anonymous, I am 11 years younger then that Bastard age bar but I will still accept that title, lol!
thanks for the offer, but where do you live?
__________________
I do stuff for reasons. |
#14
|
||||
|
||||
SW of Dayton, OH. If you like our cows and corn, you'll love our meth!
__________________
Clutch Guys Matter _______________________________________ 53 Studebaker, 400P/th400/9" 64 F-85 72 4-4-2 Mondello's VO Twister II 84 Hurst/Olds #2449 87 Cutlass Salon 54 Olds 88 sedan |
#15
|
|||
|
|||
Quote:
|
#16
|
||||
|
||||
Well if your intake is already gasket matched to the 1233 gasket then you need to take that 1/8” of taller roof height 1.5 inches into the head runner so the neck down back to stock size is not as severe and disturbing to the air mass!
__________________
I do stuff for reasons. |
The Following User Says Thank You to 25stevem For This Useful Post: | ||
#17
|
|||
|
|||
yeah, that is what i was thinking. thanks for your help, greatly appreciated.
|
Reply |
Thread Tools | |
Display Modes | |
|
|