FAQ |
Members List |
Social Groups |
Calendar |
Search |
Today's Posts |
|
#1
|
||||
|
||||
Thread sealent from fuel line to rear carb
I have a leak (drip) coming from the threads for my rear carb fuel line to the rear carb.
Is there a sealent I can use to fix this? Thanks, FB66 |
#2
|
|||
|
|||
Never use any sealant on fuel components
|
#3
|
|||
|
|||
Thanks there Warrior. The link that I received on line didn't show the general topic of tri power. Maybe you can contact the administrator and fix that....
|
#4
|
||||
|
||||
How do I fix the drip? I tighten it as tight as I can get it. It still leaks. Should I order a new block? the brass could be worn out.
Not even a little Permatex? Should I order a new block? the brass could be worn out. FB66 |
#5
|
||||
|
||||
Quote:
Try loosen the nut and put a drop of engine oil under the nut before tighten it, tighten and loosening the nut a couple of times and tighten the last time just a little more (no gorilla arms) to seat the flare. I always get them drip-free this way. FWIW |
#6
|
||||
|
||||
Quote:
Not sure where under the nut is? I think I have an idea. FB66 |
#7
|
|||
|
|||
There is a post on this site.You can buy copper flair gaskets used in thr AC biz.They work great on tripower fuel lines.I use them on all my builds from day one.Tom
|
#8
|
|||
|
|||
I guess if you don't mind the smell of gas inside your car, and remember those drips turn into a fine mist that will eventually burn your car down. Do it right you won't try Teflon or so sealant on a flared brake line, I hope. How much will it cost to fix it correctly and safely, less than the cost of a fire I think....
|
#9
|
|||
|
|||
I got some sealant at the local home improvement store that can be used with gasoline. I brushed some on every fitting from the tank to the carb, seems good so far.
|
#10
|
||||
|
||||
If fuel is leaking from the flare nut that screws into the brass fitting, there are two possible solutions. The reason it leaks is because the flare on the tubing has been squeezed flat due to overtightening or many assembly/disassembly cycles.
One fix was mentioned above--using copper flare gaskets. They look like Chinese hats and are available on line--look for flare fitting gaskets. The other fix is to replace the fuel line. If you want one, PM me. I have this line, freshly flared.
__________________
BONESTOCK GOATS '64 GTO Tripower Hardtop (Wife's Car) '64 GTO Tripower Post Coupe (My Car) '99 Bonneville SE Sedan |
#11
|
|||
|
|||
Don't use thread sealant unless the fitting seals on the threads. The threads are tapered in that case, like NPT. If not then your flare or gasket is what it at fault and THAT is what needs to be replaced.
|
#12
|
||||
|
||||
Thread sealant needs to be used on the fittings that screw into the carbs, not on the flare nuts on the fuel lines.
I use Permatex liquid sealant with Teflon on the tapered fittings. It is impervious to gasoline and works well in this application.
__________________
BONESTOCK GOATS '64 GTO Tripower Hardtop (Wife's Car) '64 GTO Tripower Post Coupe (My Car) '99 Bonneville SE Sedan |
#13
|
|||
|
|||
Quote:
If someone wants to risk it, lean-out their engine and turn a piston into swiss-cheese, knock yourself out. It is not my car. |
#14
|
||||
|
||||
Quote:
Common sense dictates being careful not to allow any tape or liquid sealant on the ends of the fittings where it will enter the float bowl and cause problems. I prefer the liquid sealant because it's less likely to cause a problem--easy to wipe off the end of a fitting if you inadvertently apply it to the end of a fitting. Common sense also dictates not tightening the brass fittings excessively, whether using Teflon products or not. The fittings only need to be tight enough to stay in place while you install the fuel lines. It is common on these 50+ year old carbs to find that the female threads are stretched to the extent that the brass fittings bottom before they're tight. In some cases, you can get a decent seal by using several wraps of Teflon tape, but in most cases, a sleeve needs to be installed by someone with the proper equipment to save the carb from the scrap heap. There is no need to apply any sealant to the flare nuts or flares on the fuel lines. I apply a small amount of oil to the fuel line flare where the nut contacts it so, when tightening the flare nut, the fuel line does not twist and distort. I've done hundreds of Tripowers as described above with no problems as a few posters have suggested. Common sense does wonders.
__________________
BONESTOCK GOATS '64 GTO Tripower Hardtop (Wife's Car) '64 GTO Tripower Post Coupe (My Car) '99 Bonneville SE Sedan |
#15
|
||||
|
||||
https://www.grainger.com/product/PAR...e-Gasket-5WRW2
I posted a link above for the copper flares Tom S was refering to. I used them and haven't had any problems.
__________________
1965 GTO 389 Tri-Power 4-Speed Johnny |
#16
|
|||
|
|||
leak
Post #8 x 2,been using GM liquid teflon since it first came out,no problems !
|
#17
|
||||
|
||||
Sealant on flare fittings can do nothing but harm.
Teflon tape on tapered fittings is a wonderful thing........................FOR THOSE OF US THAT SELL CARBURETOR KITS, BY ALL MEANS, USE IT!!!!!!! (See post 10 above). Teflon liquid or paste on tapered fittings CAN cause carburetor failure. Teflon is a wonderful lubricant. VERY easy to crack a carburetor housing with the use of Teflon paste or liquid. Since I still have 150,000 + carburetors for sale, USE IT, then I can sell you a carburetor! Jon.
__________________
"Good carburetion is fuelish hot air". "The most expensive carburetor is the wrong one given to you by your neighbor". If you truly believe that "one size fits all" try walking a mile in your spouse's shoes! Owner of The Carburetor Shop, LLC (of Missouri). Current caretaker of the remains of Stromberg Caburetor, and custodian of the existing Carter and Kingston carburetor drawings. |
#18
|
|||
|
|||
Teflon
Hello, Dick and I mean use on pipe threads only. Sorry for the confusion.
|
#19
|
||||
|
||||
I think I am going to buy a new line and block. It think it is worn out over the years.
FB66 |
#20
|
||||
|
||||
You only need a new line or the copper gaskets. The brass fitting is not worn out.
__________________
BONESTOCK GOATS '64 GTO Tripower Hardtop (Wife's Car) '64 GTO Tripower Post Coupe (My Car) '99 Bonneville SE Sedan |
Reply |
|
|