Forum: Pontiac - Street
Today, 04:59 PM
|
Replies: 1
Views: 1
|
Forum: Pontiac - Street
Today, 04:54 PM
|
Replies: 1
Views: 1
|
Forum: THE LOBBY
Today, 04:04 PM
|
Replies: 25
Views: 1,097
I was thinking that, if anything, GM could just...
I was thinking that, if anything, GM could just produce a little car called a GTO. You wouldn't need the whole Pontiac thing, and they could sell it at any dealership. But with the demise of these...
|
Forum: Pontiac - Street
Today, 03:34 PM
|
Replies: 22
Views: 540
|
Forum: Pontiac - Street
Today, 03:30 PM
|
Replies: 22
Views: 540
So, on that note about the EGR valve, I do not...
So, on that note about the EGR valve, I do not have one installed. I did purchase one. It's got the two take off ports, one to the carb (?), and one to the vacuum advance on the distributor.
The...
|
Forum: Pontiac - Street
Yesterday, 06:35 PM
|
Replies: 22
Views: 540
Hey, Mgarblik,
My condition is exactly as you...
Hey, Mgarblik,
My condition is exactly as you have described. I closed the choke blade a bit and then more, and it ran better and better. Not 100%, though. The vacuum is less than 15 inches, and...
|
Forum: Pontiac - Street
04-26-2024, 02:29 PM
|
Replies: 22
Views: 540
Thanks for the suggestions so far.
So, I can...
Thanks for the suggestions so far.
So, I can definitely eliminate a vacuum leak. I disconnected and plugged everything.
The fuel line gets warm but not overly hot
There’s no EGR valve on this...
|
Forum: Pontiac - Street
04-26-2024, 12:10 PM
|
Replies: 22
Views: 540
|
Forum: Pontiac - Street
04-26-2024, 12:06 PM
|
Replies: 22
Views: 540
Rough idle when warmed up
I'm trying to figure out why my engine starts to stumble and runs rough when it's warmed up. When I start it cold, it sounds great. Sharp engine pulses, sounds tight. Then, after it warms up, it...
|
Forum: THE LOBBY
04-24-2024, 07:27 AM
|
Replies: 18
Views: 618
Rock Auto for me. Mostly because their website...
Rock Auto for me. Mostly because their website is intuitive and easy to navigate. Also, for me, they figure out the exchange and shipping to me here in Canada, so I know exactly what I'm paying I...
|
Forum: Pontiac - Street
04-19-2024, 05:26 PM
|
Replies: 4
Views: 206
|
Forum: Pontiac - Street
04-19-2024, 11:13 AM
|
Replies: 4
Views: 206
‘67 LeMans with AC clutch fan noise
I finally have the LeMans running well. It’s really a pleasure to drive now. But one thing that I’ve found is that the clutch fan is very noisy. It’s the original 19.5” AC fan in the original...
|
Forum: 66-67 GTO Tempest & LeMans TECH
04-12-2024, 07:55 PM
|
Replies: 12
Views: 514
It's never been easier to do, new or used. The...
It's never been easier to do, new or used. The easiest and most economical way is a disc brake setup from a '69 to '72 A body. The whole thing literally slips in between the upper and lower ball...
|
Forum: THE LOBBY
04-11-2024, 07:09 PM
|
Replies: 10,203
Views: 1,714,407
|
Forum: THE LOBBY
04-11-2024, 12:28 PM
|
Replies: 10,203
Views: 1,714,407
|
Forum: THE LOBBY
04-09-2024, 03:21 PM
|
Replies: 10,203
Views: 1,714,407
Such a deal!
...
Such a deal!
https://www.facebook.com/marketplace/item/1100246944644906/?ref=search&referral_code=null&referral_story_type=post&tracking=browse_serp%3Ac90e2133-a266-42f7-8c47-11d88eec6e79
|
Forum: THE LOBBY
04-02-2024, 12:09 PM
|
Replies: 10,203
Views: 1,714,407
|
Forum: THE LOBBY
03-31-2024, 07:51 AM
|
Replies: 10,203
Views: 1,714,407
Nice machine. Too rich for my blood.
...
Nice machine. Too rich for my blood.
https://bringatrailer.com/listing/1961-pontiac-catalina-super-duty/?utm_source=dm&utm_medium=email&utm_campaign=2024-03-30
|
Forum: THE LOBBY
03-29-2024, 08:13 AM
|
Replies: 22
Views: 1,336
I was hired by one of the big manufacturers of...
I was hired by one of the big manufacturers of office furniture, to spearhead their development and release of an architectural wall. They cherry picked me with the usual lines about growth and...
|
Forum: Pontiac - Street
03-28-2024, 10:44 AM
|
Replies: 10
Views: 575
|
Forum: Pontiac - Street
03-28-2024, 08:15 AM
|
Replies: 10
Views: 575
Pinion depth tool
I'm getting closer to rebuilding my spare rear end. It's going to be great switching out from 2:78 to 3:55's.
I'm just wondering if anyone has used an inexpensive pinion depth tool. Something like...
|
Forum: THE LOBBY
03-24-2024, 05:31 PM
|
Replies: 452
Views: 32,711
I started ours today. It fired right up. I'm...
I started ours today. It fired right up. I'm looking forward to warmer weather for driving, but that might be a month yet.
Also bought everything needed to completely rebuild the extra rear end...
|
Forum: THE LOBBY
03-24-2024, 03:12 PM
|
Replies: 10,203
Views: 1,714,407
|
Forum: THE LOBBY
03-22-2024, 09:55 PM
|
Replies: 10,203
Views: 1,714,407
Love the VIN tag
...
Love the VIN tag
https://www.ebay.com/itm/326049645786?hash=item4bea12c4da%3Ag%3A-28AAOSwFkxl79C8&mkevt=1&mkcid=1&mkrid=711-53200-19255-0&campid=5335981329&customid=&toolid=10049
|
Forum: Pontiac - Street
03-15-2024, 02:32 PM
|
Replies: 3
Views: 225
|