Forum: Garage Sale
Yesterday, 12:48 AM
|
Replies: 0
Views: 130
Antique Buick for sale
1917 Buick model D35 touring car. Not restored, a "survivor". Bought out of Florida in 2015 with new top, and side curtains. Seats redone in black vinyl to original pattern. Electric start works. The...
|
Forum: THE LOBBY
04-30-2024, 12:45 AM
|
Replies: 468
Views: 34,137
|
Forum: Pontiac - Street
04-25-2024, 12:10 AM
|
Replies: 4
Views: 396
|
Forum: 60 & Older Pontiac TECH
04-20-2024, 01:14 AM
|
Replies: 5
Views: 350
Don't give up on repairing original fenders. I...
Don't give up on repairing original fenders. I couldn't obtain a replcement for my 1917 Buick fender after being wrecked, so I worked my butt off "rebuilding" it- here are before- and after- photos....
|
Forum: THE LOBBY
04-20-2024, 12:39 AM
|
Replies: 468
Views: 34,137
|
Forum: Pontiac - Race
04-18-2024, 12:58 AM
|
Replies: 8
Views: 621
|
Forum: THE LOBBY
04-18-2024, 12:44 AM
|
Replies: 468
Views: 34,137
|
Forum: THE LOBBY
04-09-2024, 11:43 PM
|
Replies: 468
Views: 34,137
|
Forum: Heating & Cooling TECH
04-04-2024, 11:20 PM
|
Replies: 1
Views: 259
Stopleak info
The aluminum head on my lakester's engine has some tiny leaks in the water jacket. I'm thinking of filling the head with water that contains a stopleak product, letting it sit, then drain the...
|
Forum: Pontiac - Race
04-04-2024, 12:39 AM
|
Replies: 24
Views: 1,029
I would say that only the designer of the cam...
I would say that only the designer of the cam profiles can correctly answer the spring force [not "pressure"} questions. Values such as peak negative acceleration aren't usually available to end...
|
Forum: THE LOBBY
04-04-2024, 12:22 AM
|
Replies: 6,103
Views: 532,302
|
Forum: Pontiac - Street
04-03-2024, 12:01 AM
|
Replies: 17
Views: 1,070
|
Forum: Pontiac - Race
03-24-2024, 11:49 PM
|
Replies: 11
Views: 718
|
Forum: THE LOBBY
03-22-2024, 12:34 AM
|
Replies: 47
Views: 1,658
|
Forum: Electrical Tech
03-17-2024, 12:36 AM
|
Replies: 13
Views: 782
No need to pull the distributor. Observe that...
No need to pull the distributor. Observe that points open and close when cranking. Clean the points with a points file. Observe that points spark when opening while cranking with ignition on; if not,...
|
Forum: THE LOBBY
03-16-2024, 12:28 AM
|
Replies: 178
Views: 17,266
|
Forum: Electrical Tech
03-14-2024, 12:31 AM
|
Replies: 6
Views: 490
My Chicago Electric load tester (from Harbour...
My Chicago Electric load tester (from Harbour Freight) has worked flawlessly for 40 years. Yeah, it's big and bulky, but I prefer the honest loading of the old fashioned carbon pile resistor.
|
Forum: Pontiac - Street
03-07-2024, 01:48 AM
|
Replies: 36
Views: 2,093
|
Forum: 60 & Older Pontiac TECH
03-07-2024, 01:34 AM
|
Replies: 15
Views: 929
I searched my files for rocker info of my GMC...
I searched my files for rocker info of my GMC engine. Roller rockers were merely noted as "SBC". Studs are Manley 42103-16. Pushrods are Manley 25738-16, 8.75" OAL. Cam is Crane HR grind no....
|
Forum: 60 & Older Pontiac TECH
03-05-2024, 12:48 AM
|
Replies: 15
Views: 929
|
Forum: 60 & Older Pontiac TECH
03-04-2024, 01:35 AM
|
Replies: 15
Views: 929
|
Forum: 60 & Older Pontiac TECH
03-03-2024, 12:39 AM
|
Replies: 15
Views: 929
|
Forum: Pontiac - Race
02-25-2024, 12:05 AM
|
Replies: 36
Views: 5,719
|
Forum: Pontiac - Boost
02-24-2024, 12:40 AM
|
Replies: 14
Views: 1,199
|
Forum: Pontiac - Boost
02-23-2024, 01:58 AM
|
Replies: 14
Views: 1,199
I wouldn't be too concerned about cam profiles....
I wouldn't be too concerned about cam profiles. When my hemi was broken for 1 1/2 seasons I ran a 6-71 blown alcohol 400 (-16 heads) with an ancient Crane hydraulic cam (from 1958) with good success....
|