Forum: Pontiac - Race
10-25-2022, 06:18 PM
|
Replies: 13
Views: 1,646
We like to use the st cut factory gear sets in...
We like to use the st cut factory gear sets in our TH400 builds if they are available- trouble is,they are in short supply now and pretty expensive.
We have one st. cut set in a customers 6000lb LWB...
|
Forum: Pontiac - Race
08-31-2021, 07:30 AM
|
Replies: 22
Views: 3,742
|
Forum: Pontiac - Boost
08-31-2021, 07:25 AM
|
Replies: 30
Views: 9,472
The bit I don't like about the Offy 2x4 is the...
The bit I don't like about the Offy 2x4 is the 'dog leg' in the ports, the air has to turn almost 90 degrees. When I reworked mine I cut the top of each port off and welded in a new roof so that the...
|
Forum: Pontiac - Street
08-29-2021, 08:22 AM
|
Replies: 24
Views: 3,850
Why not just get a set of 'shorty' type headers...
Why not just get a set of 'shorty' type headers made locally to suit what you have, or make a set yourself from a SBC weld it up kit but using Pontiac flanges? You could even fab a pair of log type...
|
Forum: Pontiac - Street
08-25-2021, 07:41 AM
|
Replies: 11
Views: 2,998
Put a piece of heat reflective material around...
Put a piece of heat reflective material around the filter, you can get the embossed thin alloy sheet type that can be folded,shaped,riveted etc, or the fibreglass backed cloth type that can be made...
|
Forum: Pontiac - Street
08-13-2021, 06:22 AM
|
Replies: 64
Views: 10,122
|
Forum: Pontiac - Race
08-10-2021, 07:13 AM
|
Replies: 41
Views: 9,718
Fantastic time for sure, but it does make you...
Fantastic time for sure, but it does make you realise how good Marty Palbykins runs were back in '96 , 6.95 in a 2950 lb car using a factory block just 400 cu in engine, in a 2500 lb car that would...
|
Forum: Pontiac - Race
08-10-2021, 06:59 AM
|
Replies: 2,068
Views: 368,437
|
Forum: Pontiac - Race
07-30-2021, 07:13 AM
|
Replies: 18
Views: 4,714
I've run ali rods in my Pontiacs with around...
I've run ali rods in my Pontiacs with around 80-100 psi cold start pressures, I used to heat the oil pan with a small electric fan heater before I started the car after leaving it stand for a few...
|
Forum: Pontiac - Street
07-21-2021, 05:07 PM
|
Replies: 63
Views: 12,607
|
Forum: Pontiac - Race
07-06-2021, 05:17 AM
|
Replies: 53
Views: 12,484
|
Forum: Pontiac - Street
06-18-2021, 07:55 AM
|
Replies: 18
Views: 3,375
There was recently a post where a guy in the UK...
There was recently a post where a guy in the UK bought a ready balanced rotating kit from one of the US vendors, (expecting it to be a drop in job), however the crank counterweights hit the oil pump...
|
Forum: Pontiac - Street
06-10-2021, 05:45 AM
|
Replies: 23
Views: 5,075
You wouldn't go far wrong with Valvoline VR1...
You wouldn't go far wrong with Valvoline VR1 20-50 imo. I've used it for years in everything from my race cars, camper van, my Jag road cars, wif'e Toyota, even my sons 4 stroke dirt bikes.
|
Forum: Pontiac - Street
06-05-2021, 08:25 AM
|
Replies: 76
Views: 13,970
|
Forum: Pontiac - Street
06-05-2021, 08:21 AM
|
Replies: 76
Views: 13,970
|
Forum: Pontiac - Race
06-05-2021, 08:00 AM
|
Replies: 53
Views: 12,484
|
Forum: Pontiac - Race
06-04-2021, 08:21 AM
|
Replies: 53
Views: 12,484
|
Forum: Pontiac - Street
06-03-2021, 08:02 AM
|
Replies: 76
Views: 13,970
|
Forum: Pontiac - Race
06-02-2021, 06:37 PM
|
Replies: 53
Views: 12,484
|
Forum: Pontiac - Street
06-02-2021, 06:24 PM
|
Replies: 76
Views: 13,970
There's probably only one small spot at the...
There's probably only one small spot at the largest diameter of the counterweight that will be close, I would grind a small flat at that spot - just enough to give .050" clearance. As Mgarblik said...
|
Forum: Pontiac - Street
06-02-2021, 08:41 AM
|
Replies: 76
Views: 13,970
|
Forum: Pontiac - Street
06-01-2021, 07:23 AM
|
Replies: 76
Views: 13,970
|
Forum: Pontiac - Street
05-31-2021, 07:33 AM
|
Replies: 9
Views: 1,343
|
Forum: Pontiac - Street
05-31-2021, 07:29 AM
|
Replies: 76
Views: 13,970
|
Forum: Pontiac - Street
05-31-2021, 07:26 AM
|
Replies: 10
Views: 1,697
|