Forum: Pontiac - Street
10-28-2024, 03:41 PM
|
|
Replies: 15
Views: 474
|
|
Forum: Pontiac - Race
10-28-2024, 03:37 PM
|
|
Replies: 12
Views: 401
|
|
Forum: Pontiac - Race
10-28-2024, 03:27 PM
|
|
Replies: 15
Views: 494
|
|
Forum: Performance Parts For Sale/Wanted
10-27-2024, 11:08 PM
|
|
Replies: 9
Views: 336
|
|
Forum: Pontiac - Street
10-27-2024, 03:57 PM
|
|
Replies: 27
Views: 1,065
Yeah, Sirotica, you are all wadded up.
I was...
Yeah, Sirotica, you are all wadded up.
I was not referring to you on post 22.
Said I would use you Blue Monster stuff.
And you do know that they do make some anti seize products that are also a...
|
|
Forum: Pontiac - Street
10-27-2024, 01:56 AM
|
|
Replies: 27
Views: 1,065
All wadded up ?
The point of my post was more...
All wadded up ?
The point of my post was more about "not" using Teflon tape on a car/truck than your stuff. I would use it if I had too. I prefer Permatex/Loc Tight but have used Gasolia if that was...
|
|
Forum: Pontiac - Street
10-25-2024, 05:04 PM
|
|
Replies: 27
Views: 1,065
|
|
Forum: Pontiac - Race
10-25-2024, 04:55 PM
|
|
Replies: 29
Views: 931
You do not need a roller cam, billet caps or...
You do not need a roller cam, billet caps or block fill to get what you are after.
You can do them if you want but its expensive and can be a pain. Studs and 2 bolt are fine
I would call Tim at...
|
|
Forum: Pontiac - Street
10-25-2024, 12:10 AM
|
|
Replies: 27
Views: 1,065
|
|
Forum: Pontiac - Street
10-24-2024, 04:41 PM
|
|
Replies: 27
Views: 1,065
|
|
Forum: Pontiac - Street
10-24-2024, 03:35 PM
|
|
Replies: 27
Views: 1,065
Teflon tape does not belong in a engine. Asking...
Teflon tape does not belong in a engine. Asking for trouble.
Now Permatex pipe dope with Teflon in it, sure.
I piece of Terlon tape could get stuck in your check ball, restricted pushrod hole ect....
|
|
Forum: Pontiac - Race
10-22-2024, 02:54 PM
|
|
Replies: 29
Views: 931
Dan Whittmore had a customer who he built a...
Dan Whittmore had a customer who he built a racing engine for that decided he just had to have aluminum rods. So, Dan rebuilt the engine, same cam, top end, compression ratio but with aluminum rods....
|
|
Forum: Pontiac - Street
10-20-2024, 02:59 AM
|
|
Replies: 15
Views: 683
|
|
Forum: Pontiac - Street
10-18-2024, 03:21 PM
|
|
Replies: 15
Views: 596
What ? Do you have any idea of the engine...
What ? Do you have any idea of the engine building experience the above posters have ?
If those guys say .060 matters............ it does.
Clearance is clearance, til its not.
Then you have a...
|
|
Forum: Pontiac - Street
10-17-2024, 10:27 PM
|
|
Replies: 36
Views: 1,443
|
|
Forum: Pontiac - Street
10-17-2024, 10:05 PM
|
|
Replies: 36
Views: 1,443
|
|
Forum: Pontiac - Street
10-16-2024, 03:15 AM
|
|
Replies: 15
Views: 596
What year block is this ? I do not remember...
What year block is this ? I do not remember anything .020 away on my stroker. I do not have any pics without the IJ scrapper in there.
I don't know but I would be temped to dust .040 off the corner...
|
|
Forum: Pontiac - Street
10-14-2024, 09:45 PM
|
|
Replies: 45
Views: 1,852
|
|
Forum: Performance Parts For Sale/Wanted
10-14-2024, 03:32 AM
|
|
Replies: 4
Views: 561
|
|
Forum: Pontiac - Race
10-04-2024, 11:59 PM
|
|
Replies: 15
Views: 1,262
|
|
Forum: Pontiac - Street
10-01-2024, 04:00 PM
|
|
Replies: 51
Views: 2,069
You could use some Belzona epoxy That stuff is...
You could use some Belzona epoxy That stuff is used to repair shafts that turn on babbit bearings all the time. Also used to repair large pump casings.
Far better than JB weld in my experience and I...
|
|
Forum: Pontiac - Street
09-29-2024, 03:46 PM
|
|
Replies: 45
Views: 2,416
Mic your snout, call Darrin at Nightmare, give...
Mic your snout, call Darrin at Nightmare, give him your snout measurement and he will send you a proper press fit BHJ balancer with the 4 bolt holes. Not cheap, but Made In The USA and as good as...
|
|
Forum: Pontiac - Street
09-28-2024, 03:14 AM
|
|
Replies: 49
Views: 2,046
|
|
Forum: Pontiac - Race
09-27-2024, 11:38 PM
|
|
Replies: 16
Views: 1,269
If you line up your timing chain like it shows...
If you line up your timing chain like it shows you in a Motors Manual you are up on # 6. So you need to make one crankshaft revolution and drop you distributor in if you want to be up on # !.
All my...
|
|
Forum: Pontiac - Street
09-26-2024, 04:45 PM
|
|
Replies: 44
Views: 2,144
"Sorry if that upsets some of you" ?
You put...
"Sorry if that upsets some of you" ?
You put it out there like your engine is making so much unbelievable power it upsets people.
Its not a standard dyno sheet so people have questions.
Seems...
|
