Forum: 64-65 GTO Tempest & LeMans TECH
Yesterday, 03:23 PM
|
Replies: 3
Views: 54
|
Forum: 64-65 GTO Tempest & LeMans TECH
Yesterday, 12:43 PM
|
Replies: 3
Views: 54
I don't think there is a source.
When I...
I don't think there is a source.
When I restored my '64 post car, I tried several vendors, including salvage yards with no success. I ended up using the original channels, which had very bad...
|
Forum: Members Helping Members
06-04-2024, 11:48 AM
|
Replies: 5
Views: 155
|
Forum: Members Helping Members
06-04-2024, 12:03 AM
|
Replies: 5
Views: 155
Thanks, b-man for the info.
I have the...
Thanks, b-man for the info.
I have the rebuild complete except for the pump spring. The carbs turned out well, using the NAPA rebuild kits, but, as with many kits today, the accelerator pumps are...
|
Forum: Members Helping Members
06-03-2024, 04:23 PM
|
Replies: 5
Views: 155
Non Pontiac (Corvair) Carb Part Needed
I foolishly agreed to rebuild a pair of 1964 Corvair one barrel carbs. The NAPA kits contain accelerator pumps, but without springs and retainers. One of the pumps in the two carbs is missing the...
|
Forum: Tri-Power Tech
06-01-2024, 12:06 PM
|
Replies: 3
Views: 211
|
Forum: Tri-Power Tech
05-27-2024, 11:56 AM
|
Replies: 23
Views: 882
|
Forum: Tri-Power Tech
05-26-2024, 05:32 PM
|
Replies: 23
Views: 882
|
Forum: 64-65 GTO Tempest & LeMans TECH
05-23-2024, 12:37 PM
|
Replies: 7
Views: 278
|
Forum: Tri-Power Tech
05-21-2024, 04:13 PM
|
Replies: 23
Views: 882
|
Forum: Tri-Power Tech
05-21-2024, 12:37 PM
|
Replies: 23
Views: 882
Sorry to disagree, but there are other...
Sorry to disagree, but there are other considerations about the floats. Rochester changed from brass to phenolic floats in 1968 or 1969. Quadrajets also switched to phenolic floats about the same...
|
Forum: Tri-Power Tech
05-19-2024, 08:27 PM
|
Replies: 23
Views: 882
The smaller center carb used until 1965 will...
The smaller center carb used until 1965 will accommodate the larger floats used in the end carbs. This gives the center carb a higher tolerance for excessive fuel pressure (above 5-6 psi)
I...
|
Forum: Tri-Power Tech
05-19-2024, 12:19 PM
|
Replies: 23
Views: 882
|
Forum: Tri-Power Tech
04-11-2024, 02:42 PM
|
Replies: 6
Views: 752
|
Forum: 64-65 GTO Tempest & LeMans TECH
03-22-2024, 04:49 PM
|
Replies: 96
Views: 64,314
|
Forum: Tri-Power Tech
02-16-2024, 05:58 PM
|
Replies: 10
Views: 1,334
|
Forum: THE LOBBY
02-14-2024, 01:41 PM
|
Replies: 70
Views: 4,060
Very disappointing. I believe most of us would...
Very disappointing. I believe most of us would much prefer an increase in dues rather than a digital magazine. This may be the beginning of the end of POCI. I'm 81 years old and have been a member...
|
Forum: Pontiac - Street
01-24-2024, 02:00 AM
|
Replies: 76
Views: 4,808
I"ve had a few cam failures, beginning with my...
I"ve had a few cam failures, beginning with my '57 Olds in 1962. Nearly all '57 Old's cams failed due to excessive spring pressure from the factory. Also my '64 GTO in the mid '70's and my '77 400 in...
|
Forum: 61-66 Big Pontiac TECH
01-20-2024, 05:51 PM
|
Replies: 2
Views: 693
|
Forum: 61-66 Big Pontiac TECH
01-19-2024, 05:29 PM
|
Replies: 2
Views: 693
Carter AFB
Whenever I restore an AFB, the screws, levers, and rods are bare steel. Can someone post a picture or describe to me what color they were plated when new?
I would like to do them correctly, rather...
|
Forum: Tri-Power Tech
01-19-2024, 05:23 PM
|
Replies: 11
Views: 1,029
|
Forum: 64-65 GTO Tempest & LeMans TECH
01-11-2024, 04:28 PM
|
Replies: 12
Views: 1,093
I use Rust-O-Leum #7777 or the SEM Trim Black....
I use Rust-O-Leum #7777 or the SEM Trim Black. The SEM product is easier to work with, and I've had good luck with adherence. I noticed it is available from WalMart online at $13.62.
Masking the...
|
Forum: Tri-Power Tech
12-22-2023, 05:18 PM
|
Replies: 5
Views: 1,129
|
Forum: Tri-Power Tech
12-19-2023, 04:26 PM
|
Replies: 14
Views: 3,977
Look at the center carb bracket with the curved...
Look at the center carb bracket with the curved bend and sturd with cotter pin. That portion of the bracket is designed to be bent to confirm to your throttle cable to allow wide open throttle and...
|
Forum: Tri-Power Tech
12-14-2023, 02:00 PM
|
Replies: 18
Views: 3,920
|