Forum: 68-69 GTO Tempest & LeMans TECH
06-14-2024, 05:17 AM
|
Replies: 35
Views: 4,213
I finally did the swap and wanted to share how...
I finally did the swap and wanted to share how awesome it looks. I was wanting to eventually put a fiberglass GTO front bumper on but this looks so good I'm not sure if I even want to! I did have to...
|
Forum: Pontiac - Street
06-03-2024, 03:00 PM
|
Replies: 9
Views: 449
|
Forum: Pontiac - Race
05-09-2024, 05:33 AM
|
Replies: 53
Views: 4,773
|
Forum: Pontiac - Race
05-02-2024, 12:09 PM
|
Replies: 25
Views: 1,366
I set up the intake and cut .045 off a side. It...
I set up the intake and cut .045 off a side. It lined up much nicer. The bottom was crushing the gasket a little harder than the top. So I set it back up today and took a couple thousandths more off...
|
Forum: Pontiac - Race
05-01-2024, 05:33 AM
|
Replies: 25
Views: 1,366
|
Forum: Pontiac - Race
04-30-2024, 07:52 PM
|
Replies: 25
Views: 1,366
|
Forum: Pontiac - Race
04-30-2024, 05:03 PM
|
Replies: 25
Views: 1,366
|
Forum: Pontiac - Race
04-30-2024, 03:43 PM
|
Replies: 25
Views: 1,366
Milling Intake
https://uploads.tapatalk-cdn.com/20240430/5a2a87ca0984bf86b5d772cc80235214.jpg
https://uploads.tapatalk-cdn.com/20240430/d7cc70fe30dfb8026ad0074e3c94e476.jpg...
|
Forum: Pontiac - Race
04-30-2024, 07:04 AM
|
Replies: 25
Views: 1,366
|
Forum: Pontiac - Race
04-30-2024, 06:52 AM
|
Replies: 25
Views: 1,366
|
Forum: Pontiac - Race
04-30-2024, 05:22 AM
|
Replies: 25
Views: 1,366
Milling Intake
My intake sits a little high with .062 gaskets making it so the thin area on the bottom of the port doesn't pinch down on the gasket. The intake is a ported Victor.
How do you determine exactly...
|
Forum: Pontiac - Race
03-22-2024, 07:44 AM
|
Replies: 53
Views: 4,773
|
Forum: Pontiac - Race
03-22-2024, 06:07 AM
|
Replies: 53
Views: 4,773
I just got my block and pistons back from the...
I just got my block and pistons back from the machine shop. The checked it out and said the finish of the bores were rough. They re-honed it and got me new moly top piston rings with a napier second...
|
Forum: Pontiac - Race
12-06-2023, 04:07 PM
|
Replies: 124
Views: 12,637
I have a thread on here if you search 'Splayed...
I have a thread on here if you search 'Splayed Main DIY'. I made a way to hold the block and with an indicator I measured the amount of material to remove. You may be able to do the measurement with...
|
Forum: Pontiac - Race
12-05-2023, 10:50 PM
|
Replies: 53
Views: 4,773
|
Forum: Pontiac - Race
12-04-2023, 10:21 AM
|
Replies: 53
Views: 4,773
|
Forum: Pontiac - Race
12-04-2023, 06:59 AM
|
Replies: 53
Views: 4,773
|
Forum: Pontiac - Race
12-04-2023, 06:28 AM
|
Replies: 53
Views: 4,773
I have tried everything I can so far with no...
I have tried everything I can so far with no success. The yellow glaze in the cylinders is still there and still chugs oil after the seafoam and ac delco top engine cleaner. My final attempt before I...
|
Forum: Pontiac - Race
11-29-2023, 06:18 AM
|
Replies: 46
Views: 2,776
|
Forum: Pontiac - Race
11-22-2023, 01:42 PM
|
Replies: 53
Views: 4,773
|
Forum: Pontiac - Race
11-22-2023, 07:36 AM
|
Replies: 53
Views: 4,773
|
Forum: Pontiac - Race
11-22-2023, 06:25 AM
|
Replies: 53
Views: 4,773
|
Forum: Pontiac - Race
11-19-2023, 07:59 PM
|
Replies: 53
Views: 4,773
|
Forum: Pontiac - Race
11-05-2023, 10:53 AM
|
Replies: 53
Views: 4,773
Everything went together smooth. Probably less...
Everything went together smooth. Probably less than 60 miles on it. I used total seal classic race ring pack. Pretty sure 20lb oil rings. I did just run the sea foam through it and ran it hard...
|
Forum: Pontiac - Race
11-04-2023, 09:02 AM
|
Replies: 53
Views: 4,773
|