Home Menu

Menu


          
PY Online Forums - Bringing the Pontiac Hobby Together > Search Forums > Search Results
Showing results 1 to 16 of 16
Search took 0.02 seconds. Search: Posts Made By: 1966geeto
Forum: 66-67 GTO Tempest & LeMans TECH 07-10-2014, 08:34 AM
Replies: 16
Views: 598
Posted By 1966geeto
Saw a guy use whiteout to get a depth reading on...

Saw a guy use whiteout to get a depth reading on the gears similar to using grease on a ring and pinion to see the pinion depth maybe I will try it just for the hell of it. I just hate it when the...
Forum: 66-67 GTO Tempest & LeMans TECH 07-09-2014, 08:21 AM
Replies: 16
Views: 598
Posted By 1966geeto
What brand did you go with ?

What brand did you go with ?
Forum: 66-67 GTO Tempest & LeMans TECH 07-08-2014, 08:12 AM
Replies: 16
Views: 598
Posted By 1966geeto
As usual mine is different my starter wont engage...

As usual mine is different my starter wont engage without shimming it away from the eng have 2 starters both of them do the same thing.

Was there any reason you went away from the mini starter ?
Forum: 66-67 GTO Tempest & LeMans TECH 07-07-2014, 08:04 AM
Replies: 16
Views: 598
Posted By 1966geeto
tried to do that firs go round had a bad mismatch...

tried to do that firs go round had a bad mismatch starter zing ended up having to use a 0.40 shim I would like to put a mini starter in but the funds are just not there right now.On 4 speeds very...
Forum: 66-67 GTO Tempest & LeMans TECH 07-06-2014, 07:13 PM
Replies: 16
Views: 598
Posted By 1966geeto
Starter shim proceedure

Is there anyway to pre shim a starter before putting eng in the car my 4 speed is really tight trying to slip shims in.
Forum: 66-67 GTO Tempest & LeMans TECH 02-15-2014, 02:25 PM
Replies: 32
Views: 2,360
Posted By 1966geeto
Wow what a difference thanks to all..

Well I gotta admit when I'm wrong I'm wrong when I wrote down the info from a friend on #1 position he told me on an HEI it was just before the cap screw so I had wires installed and dropped dist in...
Forum: THE LOBBY 01-23-2014, 10:25 AM
Replies: 50
Views: 3,251
Posted By 1966geeto
We had 2 local junkyards as that's what they were...

We had 2 local junkyards as that's what they were called back then I would treasure our weekly trek to see what was brought in I knew the owner of one and he would call me anytime something good...
Forum: Electrical Tech 01-12-2014, 05:22 PM
Replies: 29
Views: 1,163
Posted By 1966geeto
Do not buy anything from Procomp nightmare cust...

Do not buy anything from Procomp nightmare cust svc sucks pulled it out and rewired my car front to back went with Painless took me about 20 hrs but I soldered everything and added a bunch of relays...
Forum: 66-67 GTO Tempest & LeMans TECH 01-05-2014, 05:32 PM
Replies: 16
Views: 979
Posted By 1966geeto
NEVER USE ROPE TO SECURE COIL SPRINGS ASKING TO...

NEVER USE ROPE TO SECURE COIL SPRINGS ASKING TO GET YOUR DIGITS TAKEN OFF.That being said do your uppers now and make a plan to do your lower later or just compress the spring no big deal you can do...
Forum: 66-67 GTO Tempest & LeMans TECH 01-04-2014, 05:41 PM
Replies: 16
Views: 979
Posted By 1966geeto
If you are there I would also how are your ball...

If you are there I would also how are your ball joints do you have an air hammer and a vise if not take them to a machine shop after they are out to have them replaced if you do then it's not to bad...
Forum: 66-67 GTO Tempest & LeMans TECH 12-29-2013, 05:08 PM
Replies: 16
Views: 979
Posted By 1966geeto
Back off your ball joint nuts a couple of turns...

Back off your ball joint nuts a couple of turns and release the spindle couple good smacks at the base of the upper and lower joints then support the lower control with a jack stand will take the...
Forum: Exhaust TECH 12-12-2013, 10:16 PM
Replies: 17
Views: 1,396
Posted By 1966geeto
Will never use a u clam again expensive but well...

Will never use a u clam again expensive but well worth it.
Forum: Members Helping Members 11-25-2013, 08:11 PM
Replies: 43
Views: 2,040
Posted By 1966geeto
Eastwood MIG Welder Junk

I bought an Eastwood mig welder just to have around the shop well I have not used it much mostly small stuff no heavy welding .It stopped working a few weeks ago and I have been trying to get parts...
Forum: 66-67 GTO Tempest & LeMans TECH 11-19-2013, 07:09 PM
Replies: 50
Views: 4,047
Posted By 1966geeto
Yowza congrat's nice score I'm jealous..

Yowza congrat's nice score I'm jealous..
Forum: 66-67 GTO Tempest & LeMans TECH 10-23-2013, 05:57 PM
Replies: 20
Views: 1,409
Posted By 1966geeto
Rust

Used a bug sprayer worked great then rolled on the Zerorust used 2qts went one way then back over it the other way.
Forum: 66-67 GTO Tempest & LeMans TECH 10-23-2013, 01:25 PM
Replies: 20
Views: 1,409
Posted By 1966geeto
Under body pics

I should have taken before but was to busy prepping I pressure washed the undercarriage then treated it with picklex for adhesion purposes after the picklex dried I scuffed the whole thing with red...
Showing results 1 to 16 of 16

 
Forum Jump

All times are GMT -4. The time now is 04:36 AM.

 

About Us

The PY Online Forums is the largest online gathering of Pontiac enthusiasts anywhere in the world. Founded in 1991, it was also the first online forum for people to gather and talk about their Pontiacs. Since then, it has become the mecca of Pontiac technical data and knowledge that no other place can surpass.

 




Contact Us Home
Copyright © 2017