Home Menu

Menu


          
PY Online Forums - Bringing the Pontiac Hobby Together > Search Forums > Search Results
Showing results 1 to 11 of 11
Search took 0.01 seconds. Search: Posts Made By: bignate
Forum: Pontiac - Street 08-13-2023, 07:23 PM
Replies: 11
Views: 933
Posted By bignate
Factory bar works fine with a 12 bolt. Would...

Factory bar works fine with a 12 bolt. Would think it would be fine with a 9” as long as it’s a factory size housing, not one of the real beefy aftermarket housings.

Nate
Forum: Pontiac - Street 01-24-2023, 01:53 AM
Replies: 7
Views: 745
Posted By bignate
455 Wide Ratio Muncie Rear Gearing

Putting together a budget build roach of a ‘66 GTO to drive while I finish my Judge and dually. I have a .060” over 455 with 4 valve relief cast flat tops. Using 1970 #64 heads, 2802 cam, and ‘66...
Forum: Pontiac - Race 08-09-2022, 10:25 PM
Replies: 46
Views: 3,339
Posted By bignate
Pretty sure it’s just a scratch… one head was...

Pretty sure it’s just a scratch… one head was laying on top of the main caps of the block in the loft of the barn. I’ll look closely tomorrow and grab some more pictures.

BTW Paul, I’ll be...
Forum: Pontiac - Race 08-09-2022, 11:03 AM
Replies: 46
Views: 3,339
Posted By bignate
Yes the picture in #6 was one I grabbed from...

Yes the picture in #6 was one I grabbed from Rocky’s for sale add on here of an unmolested (except for the obvious repair) head.

Nate
Forum: Pontiac - Race 08-08-2022, 07:53 PM
Replies: 46
Views: 3,339
Posted By bignate
Ok just doing a quick cc job using a plate and a...

Ok just doing a quick cc job using a plate and a graduated cylinder I’ve come up with:

Chamber: ≈75cc
Intake port: ≈200cc

I say approximately but I’m sure it’s within 1cc either way.

I...
Forum: Pontiac - Race 08-08-2022, 01:27 PM
Replies: 46
Views: 3,339
Posted By bignate
I’m going to get these cleaned up and cc some...

I’m going to get these cleaned up and cc some chambers and ports this week. I would like to get them on a flow bench at some point too, just for curiosity’s sake.

After I get them cleaned up I’ll...
Forum: Pontiac - Race 01-22-2014, 03:59 PM
Replies: 123
Views: 7,396
Posted By bignate
I don't have any real world experience with it,...

I don't have any real world experience with it, but I have been researching a supercharged E-85 application I'd like to build someday.

Everything I have seen online about E-85 is that no one...
Forum: 69-71 Judges only TECH 01-22-2014, 02:14 PM
Replies: 107
Views: 4,800
Posted By bignate
Bringing this thread back from the dead. I...

Bringing this thread back from the dead.

I just noticed that my Judge build sheet has a "515" in box 74 and the other Baltimore sheets posted here box 74 is blank. Anybody have a clue what this...
Forum: THE LOBBY 12-04-2013, 08:40 PM
Replies: 29
Views: 1,261
Posted By bignate
Love this, PM sent Nate

Love this, PM sent

Nate
Forum: THE LOBBY 12-04-2013, 12:54 AM
Replies: 15
Views: 756
Posted By bignate
Get to cross one off my bucket list today

Well I just picked up a set of #614 heads tonight. I know some guys here are into rarer stuff but for a 23 year old getting a set of IV's is pretty damn cool.
...
Forum: Performance Parts For Sale/Wanted 11-23-2013, 01:53 AM
Replies: 17
Views: 2,796
Posted By bignate
Bump

Bump
Showing results 1 to 11 of 11

 
Forum Jump

All times are GMT -4. The time now is 01:42 PM.

 

About Us

The PY Online Forums is the largest online gathering of Pontiac enthusiasts anywhere in the world. Founded in 1991, it was also the first online forum for people to gather and talk about their Pontiacs. Since then, it has become the mecca of Pontiac technical data and knowledge that no other place can surpass.

 




Contact Us Home
Copyright © 2017