Home Menu

Menu


          
PY Online Forums - Bringing the Pontiac Hobby Together > Search Forums > Search Results
Showing results 1 to 10 of 10
Search took 0.02 seconds. Search: Posts Made By: Mwieczorek
Forum: Pontiac - Street 05-19-2022, 02:29 PM
Replies: 28
Views: 3,213
Posted By HWYSTR455
You're right, gonna hate that! Heheh! And mental...

You're right, gonna hate that! Heheh! And mental note on parts, uhg. I guess that's why nice ones aren't cheap.

The 'big flood', dang. I can only imagine what went up in smoke from that. Well, I...
Forum: Pontiac - Street 05-19-2022, 07:38 AM
Replies: 28
Views: 3,213
Posted By Jay S
We have used the 350 converter in our cars also...

We have used the 350 converter in our cars also and have been pretty happy with them. They seem to flash 2200 or so behind bigger cid’s. Big upgrade over some of the stock big diameter stalls, ...
Forum: Pontiac - Street 05-19-2022, 12:21 AM
Replies: 28
Views: 3,213
Posted By Sirrotica
You could put a T 350 convertor in and gain a few...

You could put a T 350 convertor in and gain a few hundred RPM stall with it. I used a 350 convertor in my 73 T/A with a 455, and a 3.08 gear, it worked well on the street, and autocross. The stock T...
Forum: Pontiac - Street 05-18-2022, 07:15 PM
Replies: 28
Views: 3,213
Posted By Half-Inch Stud
2.56:1 will require a 13" stock converter. ...

2.56:1 will require a 13" stock converter. Otherwise a risk of mushy pullaways will result.

Oh sure i could wing it and say 2800-3200 stall 10" converter, but you'd need to pay >$650 for a tight...
Forum: Pontiac - Street 04-13-2022, 06:15 PM
Replies: 22
Views: 2,741
Posted By turbo69bird
What you can get away with on a particular fuel...

What you can get away with on a particular fuel will also be determined by how rich or lean you run and your timing curve . I can run a 12 to 1 motor on pump gas if I drown it in fuel and take all...
Forum: Pontiac - Street 04-12-2022, 02:34 PM
Replies: 1
Views: 326
Posted By tom s
no diff in crankshaft length.If you take the...

no diff in crankshaft length.If you take the complete 389 front off and put it on your 400 your good.Mixing parts is here you can get in trouble.Tom
Forum: Pontiac - Street 04-11-2022, 04:16 PM
Replies: 22
Views: 2,741
Posted By 25stevem
Where has this 400 been stored that your going to...

Where has this 400 been stored that your going to look at?

Even if it happens to be indoors when you look at it and even if it has the carb on it be sure to open up the secondary’s and tilt the...
Forum: 61-66 Big Pontiac TECH 03-09-2022, 06:23 PM
Replies: 8
Views: 1,419
Posted By misterp266
1966 Assembly Line

I usually post pics like this in the vintage photo thread but thought this was a good 1966 picture for anyone that owns one.
A pic from the pit.
...
Forum: 61-66 Big Pontiac TECH 03-08-2022, 01:25 AM
Replies: 4
Views: 817
Posted By ben3843100
One more comment. If you were not aware of the...

One more comment. If you were not aware of the 15” minimum wheel size requirement for the Master Power kit and still want to run factory wheels and hubcaps, Scarebird.com does offer an updated front...
Forum: 61-66 Big Pontiac TECH 03-08-2022, 01:19 AM
Replies: 4
Views: 817
Posted By ben3843100
I have some Master Power parts on my 1966 2+2 and...

I have some Master Power parts on my 1966 2+2 and have used a couple different front disk configurations over the past couple years including Scarebird and Baer. I had no problems adapting my Master...
Showing results 1 to 10 of 10

 
Forum Jump

All times are GMT -4. The time now is 07:05 AM.

 

About Us

The PY Online Forums is the largest online gathering of Pontiac enthusiasts anywhere in the world. Founded in 1991, it was also the first online forum for people to gather and talk about their Pontiacs. Since then, it has become the mecca of Pontiac technical data and knowledge that no other place can surpass.

 




Contact Us Home
Copyright © 2017