Showing results 1 to 20 of 20
Search took 0.02 seconds.
Search: Posts Made By: Curious George
Forum: Pontiac - Race 04-28-2024, 07:16 PM
Replies: 11
Views: 397
Posted By 73LeMans
Yup, Jones racing products will sell you one too....

Yup, Jones racing products will sell you one too. Its in their catalog under Drive Hubs

Jones Racing Drive hubs (https://www.jonesracingproducts.com/#p=4)
...
Forum: Pontiac - Race 04-28-2024, 10:56 AM
Replies: 11
Views: 397
Posted By Mean Green
The Star Machine mandrel has what you're looking...

The Star Machine mandrel has what you're looking for.
Forum: Pontiac - Race 10-16-2023, 06:15 AM
Replies: 18
Views: 1,521
Posted By JSchmitz
That's a huge gain! VERY nice car! More pics...

That's a huge gain! VERY nice car! More pics please.
Forum: Pontiac - Race 10-13-2023, 09:46 PM
Replies: 10
Views: 902
Posted By slowbird
Lol no it hasn't been running since the upgrade

Lol no it hasn't been running since the upgrade
Forum: Pontiac - Race 10-13-2023, 09:25 PM
Replies: 10
Views: 902
Posted By PAUL K
You notice much difference in ET or how the...

You notice much difference in ET or how the chassis reacts?
Forum: Pontiac - Race 10-13-2023, 09:00 PM
Replies: 10
Views: 902
Posted By slowbird
Here are some pics of mine. We set it up so...

Here are some pics of mine. We set it up so fenders can ve easily remove but stock nose stays on.
Forum: Pontiac - Race 10-13-2023, 08:45 PM
Replies: 10
Views: 902
Posted By Johnny406
What motor plates did you Gentlemen, use?

What motor plates did you Gentlemen, use?
Forum: Pontiac - Race 10-13-2023, 06:09 PM
Replies: 10
Views: 902
Posted By BDHABT
We also have one on our 2nd gen;don't think there...

We also have one on our 2nd gen;don't think there are any cons.

We did'nt order it with foward bars though.My chassis guy added those himself,and tied it into the cage.
Forum: Pontiac - Race 10-13-2023, 09:20 AM
Replies: 10
Views: 902
Posted By slowbird
I have one installed on my 2nd gen bird, very...

I have one installed on my 2nd gen bird, very nice and very light compared to stock frame rails
Forum: SOLD Pontiacs 09-15-2023, 10:15 AM
Replies: 9
Views: 2,086
Posted By lugnutx2
1965 Tempest wagon $6500

Has the usual rust for a Midwest car, 326, automatic, PS,PB, it starts and stops well enough to load. The car has had a clean, green MO title for 20 years, now for some reason the State is trying to...
Forum: Pontiac - Boost 08-26-2023, 08:05 PM
Replies: 16
Views: 1,313
Posted By charlie66
No problem, I rolled my pipes up high by the...

No problem,

I rolled my pipes up high by the fender on top of the wheel well to keep them away from the engine so i can access my plugs easy .. Maybe you could try that too.

Do you have a...
Forum: Pontiac - Race 08-02-2023, 08:20 AM
Replies: 15
Views: 860
Posted By firechickenman
I believe "better" would be front and mid plates....

I believe "better" would be front and mid plates. It takes all the twisting force away from the block. I've been running solid motor mount and a rubber trans mount for years. I feel like I've...
Forum: Pontiac - Race 04-20-2023, 08:41 AM
Replies: 12
Views: 1,167
Posted By grandville455
I thought less timing would move that mark more...

I thought less timing would move that mark more towards the tip and not the base? That's how i've always understood it atleast
Forum: Pontiac - Race 04-20-2023, 06:47 AM
Replies: 12
Views: 1,167
Posted By charlie66
I would take 2 to 3 out .

I would take 2 to 3 out .
Forum: Pontiac - Race 01-25-2022, 06:32 PM
Replies: 80
Views: 11,243
Posted By Steve C.
Opinion off the internet.... You really need...

Opinion off the internet....

You really need to keep the water moving at all times, even if it's just recirculating in the block as the existing system does when cold. One good reason for setting...
Forum: Pontiac - Street 11-01-2017, 11:45 AM
Replies: 39
Views: 3,211
Posted By mysticmissle
i have 2 cars that run on e85. 64 gto is...

i have 2 cars that run on e85. 64 gto is registered but a bit too low to see much mor ethan a blast down the street and back. it is a 462 about 12:1 compression 4150/claw by mark sullens. It will...
Forum: Pontiac - Street 10-31-2017, 11:34 AM
Replies: 39
Views: 3,211
Posted By Formulajones
I do....all the time. As does most everyone...

I do....all the time. As does most everyone else that lives here. It's 200 miles round trip for me to hit any major show or cruise. And that stuff goes year round here, there is no winter down...
Forum: Pontiac - Boost 05-21-2016, 06:50 AM
Replies: 58
Views: 2,977
Posted By charlie66
I think the head gasket does get damaged after...

I think the head gasket does get damaged after awhile by the head crushing and lose of clamp force. Not from the expansion of aluminum head.. I believe the gasket fails because it loses the clamp...
Forum: Pontiac - Boost 05-21-2016, 06:43 AM
Replies: 58
Views: 2,977
Posted By charlie66
The problem with the aluminum heads are the...

The problem with the aluminum heads are the towers fail. If that didn't happen there would be know problem. I don't really think its the studs failing because before I changed my towers I went...
Forum: Pontiac - Boost 05-20-2016, 10:04 PM
Replies: 58
Views: 2,977
Posted By v869tr6
A quick look at thermo expansion shows alum. to...

A quick look at thermo expansion shows alum. to be over twice that of cast iron.
The alum. expands, crushes the head gasket over and over and then the gasket lets go.
I believe all of the turbo...
Showing results 1 to 20 of 20

 
Forum Jump

All times are GMT -4. The time now is 05:09 AM.

 

About Us

The PY Online Forums is the largest online gathering of Pontiac enthusiasts anywhere in the world. Founded in 1991, it was also the first online forum for people to gather and talk about their Pontiacs. Since then, it has become the mecca of Pontiac technical data and knowledge that no other place can surpass.

 




Copyright © 2017