Forum: Pontiac - Street
11-26-2023, 06:52 PM
|
Replies: 24
Views: 2,186
engine surging
Stock 1970 RAIV engine with the exception of Rhoades lifters, rebuilt carb (I got the kit specific for this carb and carefully disassembled, cleaned and reassembled q-jet). Dwell at 30, timing set...
|
Forum: Pontiac - Street
01-29-2022, 05:54 PM
|
Replies: 17
Views: 3,081
George: I used the manifold vacuum port for...
George: I used the manifold vacuum port for testing engine vacuum, not the timed vacuum port on carb.
Initially the vacuum gauge read LATE IGN TIMING ( between 14 and 18 inches on gauge) and rose...
|
Forum: THE LOBBY
08-22-2020, 03:34 PM
|
Replies: 6
Views: 1,005
|
Forum: 70-73 Firebird & TA TECH
06-19-2020, 04:58 PM
|
Replies: 14
Views: 1,719
|
Forum: Pontiac - Street
05-31-2020, 01:05 AM
|
Replies: 2
Views: 1,123
|
Forum: 67-69 Firebird TECH
05-27-2020, 10:08 PM
|
Replies: 13
Views: 2,731
|
Forum: THE LOBBY
05-18-2020, 01:47 AM
|
Replies: 17
Views: 1,379
|
Forum: THE LOBBY
05-13-2020, 06:18 PM
|
Replies: 21
Views: 2,026
|
Forum: 67-79 Big Pontiac TECH
04-02-2020, 10:32 AM
|
Replies: 19
Views: 3,686
|
Forum: THE LOBBY
02-28-2020, 07:26 PM
|
Replies: 7
Views: 827
|
Forum: 67-81 Firebird & TA Parts WANTED
02-11-2020, 09:53 PM
|
Replies: 1
Views: 937
|
Forum: The Body Shop TECH
01-21-2020, 08:15 PM
|
Replies: 11
Views: 2,220
|
Forum: The Body Shop TECH
12-12-2019, 10:52 AM
|
Replies: 20
Views: 9,110
|
Forum: Members Helping Members
12-11-2019, 05:53 PM
|
Replies: 19
Views: 6,872
The spindle is not tapered. It has 1/2 x 24...
The spindle is not tapered. It has 1/2 x 24 threads it's entire length. The chuck had the 3 fingers that held the drill bit. Somehow my grandson lost those. The drill press is in an unheated garage....
|
Forum: THE LOBBY
11-05-2019, 02:38 PM
|
Replies: 14
Views: 1,547
|
Forum: Pontiac - Street
08-20-2019, 10:23 AM
|
Replies: 8
Views: 1,382
There is a plug near the distrib. base which is...
There is a plug near the distrib. base which is an oil galley plug. It can be removed and used to plumb an oil pressure gauge into. It is possible the plug may be slightly loose or not seated enough...
|
Forum: 61-77 GTO, Tempest & LeMans Parts For SALE
11-24-2018, 09:22 PM
|
Replies: 1
Views: 442
65-67 hood scoop insert
GM piece, I used the studs on my car, previous owner was going to make it ram air and made 1 cut as shown in top left of picture. The cut should be EZ to fill, repair won't be seen when installed....
|
Forum: THE LOBBY
07-30-2017, 07:38 PM
|
Replies: 37
Views: 2,679
I knew a transmission shop owner that had an...
I knew a transmission shop owner that had an Accura they rebuilt twice and it failed both times while under warranty. Their solution was to get a junkyard transmission, paint it, and put it in and...
|
Forum: 64-65 GTO Tempest & LeMans TECH
01-25-2017, 10:51 PM
|
Replies: 19
Views: 1,717
Tom may have forgotten, but his KC convertible...
Tom may have forgotten, but his KC convertible was equipped with the Verbra-Phonic rear seat speaker from the factory as confirmed by the 5 Group Code 2V on his Data Plate.
Since the decode of the...
|
Forum: Pontiac - Street
07-22-2016, 04:35 PM
|
Replies: 19
Views: 1,269
|
Forum: 67-79 Big Pontiac TECH
06-06-2016, 12:34 PM
|
Replies: 467
Views: 141,478
|
Forum: Electrical Tech
05-31-2016, 11:49 AM
|
Replies: 2
Views: 191
|
Forum: Pontiac - Street
09-17-2015, 04:42 PM
|
Replies: 3
Views: 274
|
Forum: Pontiac - Street
11-07-2014, 02:55 PM
|
Replies: 66
Views: 3,303
Adam,
Higher loading on the valvetrain is...
Adam,
Higher loading on the valvetrain is referring to camshafts with agressive ramp profiles, higher springs pressures and the like. It's not realy refering to flat tappet vs roller, since both...
|
Forum: 67-69 Firebird TECH
05-26-2014, 08:42 PM
|
Replies: 4,603
Views: 798,406
eBay sightings
I watch eBay a lot and it seems pointless to start new threads when things pop up. These two are worthy:
1969 Firebird convert 4-speed. I have a Palladium silver 350HO convert 4-speed car and I...
|