Forum: Pontiac - Street
04-14-2024, 05:05 PM
|
Replies: 4
Views: 519
The Butler lifters that Jay recommended are...
The Butler lifters that Jay recommended are Hy-Lift Johnson lifters and made in the USA they are a good lifter. If I were ever to go with flat tappet lifters again I would go with a solid cam and...
|
Forum: Pontiac - Race
04-01-2024, 07:33 AM
|
Replies: 16
Views: 842
|
Forum: 70-73 Firebird & TA TECH
01-04-2024, 04:43 PM
|
Replies: 40
Views: 4,188
|
Forum: Pontiac - Street
12-06-2023, 10:02 PM
|
Replies: 60
Views: 8,368
Cliff Ruggles
Just wanted to say, Thanks to Cliff, for being there when needed.
No, he didn’t pay me 5.00 to post this, and no it’s not a paid advertisement. I don’t usually post stuff like this, but this one...
|
Forum: Pontiac - Street
10-20-2023, 06:44 PM
|
Replies: 47
Views: 4,920
My only experience with headers vs. manifolds...
My only experience with headers vs. manifolds (other than a dedicated race car) happened when I had my first car, a ‘70 Formula 400 with the YS 330 hp 400, TH400 trans and the 3.07 open 12-bolt rear...
|
Forum: Pontiac - Street
10-20-2023, 07:13 AM
|
Replies: 194
Views: 16,125
|
Forum: Pontiac - Street
10-08-2023, 06:42 AM
|
Replies: 8
Views: 755
|
Forum: 61-66 Big Pontiac TECH
10-04-2023, 08:59 PM
|
Replies: 0
Views: 364
Addco 857 front sway bar FYI
Just finished installing all new bushings, springs and front sway bar on my 66 Catalina wagon. Man, anyone on the fence should just do it. Total 180 in drive ability and enjoyment.
Anyways, the...
|
Forum: Pontiac - Street
09-18-2023, 09:44 AM
|
Replies: 87
Views: 5,304
Folks forget these PRW rocker arms were highly...
Folks forget these PRW rocker arms were highly touted on this website about ten years ago. I recall a highly respected member (who seems to enjoy exaggerating a bit) highly recommended these rocker...
|
Forum: Pontiac - Street
08-27-2023, 06:47 PM
|
Replies: 28
Views: 1,678
|
Forum: THE LOBBY
08-26-2023, 11:20 PM
|
Replies: 7
Views: 587
|
Forum: Pontiac - Race
08-04-2023, 06:08 PM
|
Replies: 19
Views: 1,172
|
Forum: Pontiac - Street
07-30-2023, 12:04 AM
|
Replies: 85
Views: 9,005
Mike, Bud used to tell me “New does not mean...
Mike, Bud used to tell me “New does not mean good”. Just because a part or component is new doesn’t mean it complies to the desired specs. This is WHY I mic every part before it is installed in an...
|
Forum: Pontiac - Street
07-16-2023, 08:51 PM
|
Replies: 15
Views: 1,380
If it isn’t already I would make the steering...
If it isn’t already I would make the steering wheel straight according to the mark that should be on the steering shaft under the horn button. I ussually leave the horn button off and let them make...
|
Forum: THE LOBBY
07-12-2023, 12:43 PM
|
Replies: 67
Views: 10,496
|
Forum: THE LOBBY
04-07-2023, 09:09 AM
|
Replies: 128
Views: 10,314
|
Forum: Pontiac - Street
03-24-2023, 04:08 PM
|
Replies: 174
Views: 13,657
Molnar rods and cranks
I would like to thank Tom Molnar and Ed for going out of their way to make us fine Pontiac rods and cranks for our old dinosaur engines.
They went out of their way to make us a custom batch of 3.25...
|
Forum: THE LOBBY
02-27-2023, 09:01 PM
|
Replies: 113
Views: 5,895
I respect what they were. That is why I have ...
I respect what they were. That is why I have more than one brand. They all offered something in the muscle car wars. I was a teenager when all that was taking place. If you install a modern engine...
|
Forum: Pontiac - Street
02-14-2023, 12:46 PM
|
Replies: 24
Views: 2,522
|
Forum: THE LOBBY
01-30-2023, 12:04 AM
|
Replies: 32
Views: 4,050
|
Forum: Pontiac - Street
01-26-2023, 03:03 PM
|
Replies: 44
Views: 3,913
|
Forum: Pontiac - Race
01-14-2023, 01:25 AM
|
Replies: 111
Views: 8,833
Even in a controlled fatigue test of machined...
Even in a controlled fatigue test of machined test coupons, the variation in cycles to fail under identical conditions is huge. Say you test 100 parts and the first fail happens at 1000 cycles... ...
|
Forum: Pontiac - Street
12-18-2022, 02:35 AM
|
Replies: 20
Views: 2,163
|
Forum: Pontiac - Race
12-14-2022, 08:09 PM
|
Replies: 15
Views: 1,925
|
Forum: THE LOBBY
12-12-2022, 05:50 AM
|
Replies: 29
Views: 1,554
|