Home Menu

Menu


          
PY Online Forums - Bringing the Pontiac Hobby Together > Search Forums > Search Results
Page 1 of 6 1 23 Last »
Showing results 1 to 25 of 145
Search took 0.04 seconds. Search: Posts Made By: AG
Forum: Heating & Cooling TECH 09-13-2024, 08:32 AM
Replies: 33
Views: 1,168
Posted By AG
I calculated the pressure (above atmospheric)...

I calculated the pressure (above atmospheric) going 134 mph and it was about 1.2-1.5 psi if I remember correctly.
Forum: Pontiac - Street 08-24-2024, 11:33 PM
Replies: 17
Views: 914
Posted By AG
I run a 8.5" 1972 Nova rear in my race car that...

I run a 8.5" 1972 Nova rear in my race car that runs 10.0 with about 150 runs with no issue.
Forum: Pontiac - Race 08-21-2024, 09:51 AM
Replies: 66
Views: 8,406
Posted By AG
If your P/W clearance was more than recommended...

If your P/W clearance was more than recommended and your ring gaps were correct it's unlikely it would smoke. I have run P/W clearance of 0.009" with TRW forged pistons and it didn't smoke.
Forum: Pontiac - Street 08-08-2024, 11:57 AM
Replies: 67
Views: 2,067
Posted By AG
I've had that happen several times with cheap...

I've had that happen several times with cheap parts store replacements with a 400 Hp motor.
Forum: Pontiac - Street 08-06-2024, 07:29 PM
Replies: 67
Views: 2,067
Posted By AG
Sildenafil 100 mg is your friend I82, it'll put...

Sildenafil 100 mg is your friend I82, it'll put lead in your pencil.
Forum: 68-69 GTO Tempest & LeMans TECH 08-05-2024, 08:07 PM
Replies: 376
Views: 43,787
Posted By AG
My '68 FB with a 350 2 bbl and manual 3 speed...

My '68 FB with a 350 2 bbl and manual 3 speed with 3.23 gears is very peppy. It actually surprised me. It's not as peppy as my '72 LeMans vert with 455 4 bbl and 3.55 gears though.
Forum: Pontiac - Street 08-04-2024, 01:40 PM
Replies: 19
Views: 865
Posted By AG
That looks like an Olds 8.5" rear.

That looks like an Olds 8.5" rear.
Forum: Pontiac - Street 07-22-2024, 06:55 PM
Replies: 86
Views: 5,078
Posted By AG
I think the RAIV cam would be perfect. I have...

I think the RAIV cam would be perfect. I have run it in a 400 and currently have one in a 455 and it's perfect.
Forum: Pontiac - Race 07-10-2024, 10:49 AM
Replies: 7
Views: 772
Posted By AG
Without milling the pan rails, I used an extra...

Without milling the pan rails, I used an extra piece of flat cork gasket covering about 70% of the #5 cap over the regular cork rear pan seal and it worked well.
Forum: Pontiac - Street 07-05-2024, 10:44 PM
Replies: 20
Views: 1,392
Posted By AG
Slide the new pilot bearing over the trans input...

Slide the new pilot bearing over the trans input shaft before you install it.
Forum: 70-73 Firebird & TA TECH 04-26-2024, 06:16 PM
Replies: 29
Views: 2,729
Posted By AG
It looks like it has a 4-wheel drive. I love the...

It looks like it has a 4-wheel drive. I love the car but don't know why a high-end car like that doesn't have a stock like suspension.
Forum: Pontiac - Street 04-05-2024, 11:11 AM
Replies: 36
Views: 2,086
Posted By AG
I put a light coat of paint on my BHJ balancer...

I put a light coat of paint on my BHJ balancer before I had my rotating assembly balanced to prevent rust formation and there is no rust after 10 years. I also painted my reluctor wheel in my MSD...
Forum: Pontiac - Street 03-23-2024, 10:20 PM
Replies: 58
Views: 4,384
Posted By AG
It was a clients car and he has the directions. ...

It was a clients car and he has the directions. I don't remember exactly how I adjusted them but I think I used at least a full turn.
Forum: Pontiac - Street 03-10-2024, 08:05 PM
Replies: 39
Views: 3,963
Posted By AG
My race car has 0.0029"-0.0035" main clearances...

My race car has 0.0029"-0.0035" main clearances and 0.0024-0.0026" rod clearances. I use Walmart 10W-40 full syn and it has 30 psi at full heat soaked 1000 rpm idle. I have had it apart and all the...
Forum: Pontiac - Street 02-28-2024, 08:10 PM
Replies: 70
Views: 10,479
Posted By AG
i8 is the best.

i8 is the best.
Forum: Pontiac - Race 02-24-2024, 09:31 PM
Replies: 24
Views: 3,429
Posted By AG
My old bathtub Eddy chambers work best at 39...

My old bathtub Eddy chambers work best at 39 degrees timing for best mph.
Forum: Pontiac - Race 02-24-2024, 09:27 PM
Replies: 24
Views: 3,037
Posted By AG
I always do that since it's easy and free.

I always do that since it's easy and free.
Forum: Pontiac - Street 02-01-2024, 09:38 PM
Replies: 57
Views: 7,323
Posted By AG
I had it in a 1965 LeMans. I got severe...

I had it in a 1965 LeMans. I got severe wheel-hop off the line and didn't get out of it soon enough. The carrier and axles stayed in but the whole front of the housing/pinion support blew apart.
Forum: Pontiac - Street 02-01-2024, 07:33 PM
Replies: 57
Views: 7,323
Posted By AG
I have a 1971 8.2 out of a GP with a 3.07 4...

I have a 1971 8.2 out of a GP with a 3.07 4 pinion STT.
Forum: Pontiac - Street 01-29-2024, 10:12 PM
Replies: 19
Views: 1,776
Posted By AG
Less parasitic loss compared to a 9" and it's...

Less parasitic loss compared to a 9" and it's lighter, not sure about a Dana 60.
Forum: Pontiac - Street 01-25-2024, 08:16 PM
Replies: 46
Views: 5,350
Posted By AG
I installed a used RA IV cam using used HFT...

I installed a used RA IV cam using used HFT lifters in the fall of 2022 and everything worked no problem. I used 100# seat pressure CC cam lube on the cam and moly paste on the bottom of the...
Forum: Pontiac - Street 01-21-2024, 05:19 PM
Replies: 19
Views: 1,452
Posted By AG
You can get the rod bearings coated to tighten up...

You can get the rod bearings coated to tighten up the clearance. I used Calico with great success, I coat all my bearings now.
Forum: Suspension TECH 01-20-2024, 09:13 PM
Replies: 47
Views: 7,724
Posted By AG
I put a Wilwwod 1" master and proportioning valve...

I put a Wilwwod 1" master and proportioning valve on my brother's 1970 LeMans with GM front disc/ rear drum and it works great and doesn't pollute the engine bay. I called Willwood to get their...
Forum: Pontiac - Street 01-18-2024, 12:48 PM
Replies: 171
Views: 29,268
Posted By AG
I have an 8.9:1 CR 462 with a RAIV cam and Rhoads...

I have an 8.9:1 CR 462 with a RAIV cam and Rhoads lifters in my '72 convertible with RA manifolds, 7K3 heads, an HO intake and Qjet. I think it's a great combination and has very good street manners...
Forum: Pontiac - Street 01-15-2024, 09:03 PM
Replies: 39
Views: 3,686
Posted By AG
https://www.summitracing.com/parts/crt-m6907/make/...

https://www.summitracing.com/parts/crt-m6907/make/pontiac
Showing results 1 to 25 of 145
Page 1 of 6 1 23 Last »

 
Forum Jump

All times are GMT -4. The time now is 11:35 AM.

 

About Us

The PY Online Forums is the largest online gathering of Pontiac enthusiasts anywhere in the world. Founded in 1991, it was also the first online forum for people to gather and talk about their Pontiacs. Since then, it has become the mecca of Pontiac technical data and knowledge that no other place can surpass.

 




Contact Us Home
Copyright © 2017