Home Menu

Menu


          
PY Online Forums - Bringing the Pontiac Hobby Together > Search Forums > Search Results
Page 1 of 20 1 2311 Last »
Showing results 1 to 25 of 500
Search took 0.18 seconds. Search: Posts Made By: steve25
Forum: Pontiac - Street Yesterday, 08:51 AM
Replies: 19
Views: 517
Posted By steve25
I can’t put enough emphasis on checking your...

I can’t put enough emphasis on checking your total timing with out vacuum advance hooked up at 5000 rpm to confirm that it’s not over advancing on you.
Forum: Pontiac - Street 05-31-2024, 04:10 PM
Replies: 21
Views: 587
Posted By steve25
That seals OD coating is likely to dry out and...

That seals OD coating is likely to dry out and cause a issue before the actual crank seal lip does..

Get a good seal with a metal OD and just put it in with some gray form-A- gasket and then sleep...
Forum: Pontiac - Street 05-28-2024, 05:45 PM
Replies: 36
Views: 1,237
Posted By steve25
With brand new plugs and not being at a track it...

With brand new plugs and not being at a track it will take at least 3 full throttle thru the gears runs to see anything worthwhile in terms of the plug being too hot or not.
And they need to be...
Forum: Pontiac - Street 05-28-2024, 05:22 PM
Replies: 13
Views: 712
Posted By steve25
If it’s as you say a stock-ish deal, then with...

If it’s as you say a stock-ish deal, then with stock springs and retainers that cams .470” lift might have been too much for the clearance set up on number 4.

Even with just 290 psi of open...
Forum: Pontiac - Street 05-25-2024, 03:51 PM
Replies: 5
Views: 307
Posted By steve25
What heads are you running? The size of the...

What heads are you running?
The size of the chamber effects the level of idle vacuum you pull also.

I would also hope that with a cam of those specs that your running at least 9.5 to 1.?
Forum: Pontiac - Street 05-25-2024, 07:07 AM
Replies: 12
Views: 511
Posted By steve25
Go watch the Engine masters air filter shoot out...

Go watch the Engine masters air filter shoot out test and then decide if you still want to run a air lid with a filter in it a long with a normal side flow filter.
Forum: Pontiac - Street 05-24-2024, 11:24 AM
Replies: 3
Views: 207
Posted By steve25
The hole in the air horn gasket for the pump...

The hole in the air horn gasket for the pump shaft could be getting oblonged, or the pump cup itself may not be sealing in the well and then instead of fuel only moving out into the primary's it...
Forum: Pontiac - Street 05-23-2024, 08:09 PM
Replies: 22
Views: 807
Posted By steve25
How many here had a 78 TA with the W72 package,...

How many here had a 78 TA with the W72 package, let me jump the gun here.

I had two, one with 40k miles on it and another with 80k on it when I got it .
Both auto trans models.
This 80k one when...
Forum: Pontiac - Street 05-23-2024, 03:55 PM
Replies: 22
Views: 807
Posted By steve25
I would have no concern with longevity running...

I would have no concern with longevity running such a block provided these guidelines are met.

Lighter aftermarket rods and pistons are used.

The stroke stays at 3.750”

A good balance job...
Forum: Pontiac - Street 05-14-2024, 06:08 PM
Replies: 8
Views: 359
Posted By steve25
If you narrow it down to the front then jack the...

If you narrow it down to the front then jack the front up on each side and have someone spin the tire while you apply the brakes lightly.

If you do not feel anything then you know the issue is due...
Forum: Pontiac - Street 05-14-2024, 05:43 PM
Replies: 15
Views: 687
Posted By steve25
How do you grind a Crankshaft this big?

I’am stunned!
Forum: Pontiac - Street 05-14-2024, 12:51 PM
Replies: 18
Views: 599
Posted By steve25
Johnny on my last motor I did springs on in car I...

Johnny on my last motor I did springs on in car I had to use rope.
The motor had thin rings and a non rope rear seal, so with air in one cylinder it would just spin over very slowly.
When I lowered...
Forum: Pontiac - Street 05-13-2024, 06:00 AM
Replies: 18
Views: 599
Posted By steve25
The stock valve seals on any regular production...

The stock valve seals on any regular production Pontiac V8 are just the O rings like you used on your assembly of the 6X heads.

To change them in the car you need bring the piston up to TDC, stuff...
Forum: Pontiac - Street 05-08-2024, 07:58 PM
Replies: 32
Views: 1,770
Posted By steve25
While the 71 96 casting heads flow good enough to...

While the 71 96 casting heads flow good enough to make 350 Hp even without headers they will not get your compression with a 400 up into the 9 to 1 range without milling them .060” on the deck and...
Forum: Pontiac - Street 05-08-2024, 06:12 PM
Replies: 64
Views: 3,223
Posted By steve25
8.750” to 9.500” should do it easy.

8.750” to 9.500” should do it easy.
Forum: Pontiac - Street 05-06-2024, 06:02 AM
Replies: 10
Views: 602
Posted By steve25
You shoukd also consider the fact that aluminum...

You shoukd also consider the fact that aluminum heads when fully up to temp will grow taller by .006" to .008" thus releaving some of your preload adjustment.

If you assume that you have perfect...
Forum: Pontiac - Street 05-05-2024, 03:11 PM
Replies: 7
Views: 364
Posted By steve25
Use a vented cap since it will never get get...

Use a vented cap since it will never get get clogged off with age like the hose can.
Forum: Pontiac - Street 05-05-2024, 03:09 PM
Replies: 10
Views: 602
Posted By steve25
Is your valley pan and Intake on the motor. ...

Is your valley pan and Intake on the motor.

Has the motor been run before, or are the lifters empty?
Forum: Pontiac - Street 05-03-2024, 02:30 PM
Replies: 19
Views: 821
Posted By steve25
I am trying to find my notes from 25 years ago ...

I am trying to find my notes from 25 years ago in regards to the valve to piston clearance deal, but here’s what I recall off of the top of my head.
Using 428 pistons in a 421 build with its...
Forum: Pontiac - Street 05-03-2024, 11:30 AM
Replies: 20
Views: 1,007
Posted By steve25
With only 3 psi to feed even just one Carb no...

With only 3 psi to feed even just one Carb no less 3 would not run the motor to full throttle and expect nothing less then the motor falling on its face within 4 seconds.or by the time you get...
Forum: Pontiac - Street 05-03-2024, 09:31 AM
Replies: 1
Views: 168
Posted By steve25
25ft lbs will get it done. Just first confirm...

25ft lbs will get it done.
Just first confirm that all the bolts thread in easy by hand and will not bottom out without having the manifold already clamped down.
Forum: Pontiac - Street 05-01-2024, 07:42 PM
Replies: 24
Views: 1,107
Posted By steve25
With a 4.120” to a 4.150” bore and a 3.750”...

With a 4.120” to a 4.150” bore and a 3.750” stroke and a 72 Cc head every 4 CCs will change the compression close enough to a 1/4 point in regards to a street motor .
Forum: Pontiac - Street 04-24-2024, 11:46 AM
Replies: 37
Views: 2,532
Posted By steve25
I am sure that Rhoads does not make a living off...

I am sure that Rhoads does not make a living off of just Pontiac lifters!

People who do not use them and have over Cam’ed motors are some of the other brands that we blow into the weeds with our...
Forum: Pontiac - Street 04-21-2024, 07:29 AM
Replies: 6
Views: 556
Posted By steve25
Post 3 has the solution. To drop it out let...

Post 3 has the solution.

To drop it out let both headers dangle on there bolts as far as possible and loosen up the collectors bolts.

If you put anti-seize on at lease one side of your header...
Forum: Pontiac - Street 04-19-2024, 08:25 AM
Replies: 55
Views: 4,152
Posted By steve25
Two big fuel bowls and two needles and seats can...

Two big fuel bowls and two needles and seats can at times solve the problem of not having a pump back at the tank purely due to the fuel volume on hand.

The root cause many times is the G force...
Showing results 1 to 25 of 500
Page 1 of 20 1 2311 Last »

 
Forum Jump

All times are GMT -4. The time now is 02:34 PM.

 

About Us

The PY Online Forums is the largest online gathering of Pontiac enthusiasts anywhere in the world. Founded in 1991, it was also the first online forum for people to gather and talk about their Pontiacs. Since then, it has become the mecca of Pontiac technical data and knowledge that no other place can surpass.

 




Contact Us Home
Copyright © 2017