Forum: Pontiac - Race
Today, 09:30 PM
|
Replies: 1
Views: 2
I used a plastic putty knife to get the thick...
I used a plastic putty knife to get the thick stuff and then clean it with thinner.
What I started doing a couple years ago that works very well. I have been applying a clear wrap on the lower...
|
Forum: Pontiac - Street
Today, 06:06 PM
|
Replies: 39
Views: 1,041
Ok, last pic before i drive you guys to...
Ok, last pic before i drive you guys to drinking..............this was from last nite to most of the day today.
When i started this thread i knew i had a leak, my issue was if i didnt run the car...
|
Forum: Electrical Tech
Today, 04:29 PM
|
Replies: 3
Views: 38
|
Forum: The Body Shop TECH
Today, 03:11 PM
|
Replies: 4
Views: 92
|
Forum: THE LOBBY
Today, 03:04 PM
|
Replies: 638
Views: 46,721
|
Forum: Pontiac - Street
Today, 02:09 PM
|
Replies: 24
Views: 582
are you using vac. advance. if so, limit it to...
are you using vac. advance. if so, limit it to about 12-14 deg. if not, install one. it is absolute necessary on a street engine, and works in conjunction with the power valve you are about to...
|
Forum: Pontiac - Street
Today, 10:49 AM
|
Replies: 12
Views: 271
|
Forum: Pontiac - Street
Today, 10:35 AM
|
Replies: 12
Views: 271
michael,
from one...
michael,
from one 24(+)year-project-finally-done-first-drive-owner to another ... congrats, man. car looks and sounds badass.
I took first drive in my 69 Judge, that I used to beat the snot out...
|
Forum: Pontiac - Street
Today, 09:36 AM
|
Replies: 12
Views: 271
24 year project - first drive!
Finally got the car inspected yesterday, and drove it for the first time ever. Was a very anxious drive to town to get to the garage (6 miles), new brakes/engine/clutch/trans/gears, was not used to...
|
Forum: Members Helping Members
Today, 08:53 AM
|
Replies: 6
Views: 114
|
Forum: Pontiac - Street
Yesterday, 10:23 PM
|
Replies: 40
Views: 803
|
Forum: Pontiac - Street
Yesterday, 09:48 PM
|
Replies: 39
Views: 1,041
Hey Drake, sorry to hear about your...
Hey Drake, sorry to hear about your situation.............im not really complaining, just trying to figure out this oil leak deal................had to look up where your at, 140 miles from...
|
Forum: The Body Shop TECH
Yesterday, 09:23 PM
|
Replies: 7
Views: 193
|
Forum: 61-77 GTO, Tempest & LeMans Parts WANTED
Yesterday, 09:07 PM
|
Replies: 11
Views: 229
|
Forum: THE LOBBY
Yesterday, 09:04 PM
|
Replies: 638
Views: 46,721
|
Forum: 66-67 GTO Tempest & LeMans TECH
Yesterday, 08:18 PM
|
Replies: 1
Views: 63
|
Forum: THE LOBBY
Yesterday, 08:11 PM
|
Replies: 638
Views: 46,721
|
Forum: Pontiac - Race
Yesterday, 08:09 PM
|
Replies: 124
Views: 12,497
Always make sure you verify you have enough...
Always make sure you verify you have enough clearance between the piston and the valve. With head gasket installed and head torqued, not full torque but you should at least partially crush the head...
|
Forum: 67-69 Firebird TECH
Yesterday, 03:53 PM
|
Replies: 4,287
Views: 713,098
|
Forum: 70-73 Firebird & TA TECH
Yesterday, 01:09 PM
|
Replies: 2
Views: 84
|
Forum: Pontiac - Street
Yesterday, 12:04 PM
|
Replies: 18
Views: 399
I haven’t seen or read of any failures with the...
I haven’t seen or read of any failures with the Progression Ignition. And usually those pop-up easily on a google search.
As far as issues with compatibility with factory tachs, I only know of the...
|
Forum: Pontiac - Street
Yesterday, 11:05 AM
|
Replies: 18
Views: 399
|
Forum: Pontiac - Street
Yesterday, 08:41 AM
|
Replies: 15
Views: 243
Skip's got it right, just add the fitting to...
Skip's got it right, just add the fitting to what you have now. I would open up the "slot" so you can move the attachment point up/down to nail down the best geometry. You will still have PLENTY...
|
Forum: Pontiac - Street
Yesterday, 08:15 AM
|
Replies: 15
Views: 243
|
Forum: Pontiac - Street
Yesterday, 07:30 AM
|
Replies: 40
Views: 803
|