Forum: Pontiac - Street
Today, 05:40 AM
|
|
Replies: 10
Views: 259
Couple of things to mention.
IF you install...
Couple of things to mention.
IF you install a new SI style alternator make sure that the battery is FULLY charged. If you don't it goes to full charge and works the piss out of the regulator and...
|
|
Forum: Pontiac - Street
Today, 03:50 AM
|
|
Replies: 10
Views: 259
|
|
Forum: THE LOBBY
Today, 01:04 AM
|
|
Replies: 101
Views: 4,477
|
|
Forum: THE LOBBY
Yesterday, 11:10 PM
|
|
Replies: 101
Views: 4,477
|
|
Forum: Pontiac - Street
Yesterday, 10:49 PM
|
|
Replies: 3
Views: 149
|
|
Forum: Pontiac - Street
Yesterday, 05:31 PM
|
|
Replies: 8
Views: 198
|
|
Forum: Pontiac - Street
Yesterday, 04:30 PM
|
|
Replies: 15
Views: 299
|
|
Forum: 66-67 GTO Tempest & LeMans TECH
Yesterday, 04:21 PM
|
|
Replies: 4
Views: 116
|
|
Forum: Pontiac - Street
Yesterday, 03:34 PM
|
|
Replies: 8
Views: 198
|
|
Forum: THE LOBBY
Yesterday, 03:29 PM
|
|
Replies: 3
Views: 245
|
|
Forum: Pontiac - Street
Yesterday, 03:11 PM
|
|
Replies: 8
Views: 198
When I was shopping for my setup, I went in...
When I was shopping for my setup, I went in looking at a forged crank. Butler talked me out of it and told me that a cast crank would be just fine if I'm not running any power adders. If you chose to...
|
|
Forum: Pontiac - Street
Yesterday, 02:25 PM
|
|
Replies: 28
Views: 689
|
|
Forum: 67-69 Firebird TECH
Yesterday, 01:59 PM
|
|
Replies: 15
Views: 712
|
|
Forum: Pontiac - Street
Yesterday, 11:59 AM
|
|
Replies: 25
Views: 754
I read of that, and looked into it;
The...
I read of that, and looked into it;
The purported "067" cam is actually another 066 replacement cam; but don't just take my word for it, here are the spec's:
Butler exclusive "067-RA" specs:
...
|
|
Forum: Electrical Tech
Yesterday, 11:49 AM
|
|
Replies: 5
Views: 134
Back-up lamp switch= Muncie 4 speed transmission
Here is a jpeg from a long time ago. This is a 66 GTO 4 speed transmission but a 65 GTO would be the same as far as that reverse lamp switch and wiring goes.
Where the twin wires pass thru the...
|
|
Forum: Pontiac - Street
Yesterday, 11:33 AM
|
|
Replies: 13
Views: 289
|
|
Forum: Pontiac - Street
Yesterday, 11:30 AM
|
|
Replies: 25
Views: 754
Couple things.
Most machine shops now use a...
Couple things.
Most machine shops now use a finish of 50 as SOP, since many OEs use steel gaskets, AND because many request it due to aluminum head availability.
Quench. Quench makes a...
|
|
Forum: Pontiac - Street
Yesterday, 10:06 AM
|
|
Replies: 28
Views: 689
Just to say, gapless rings are junk IMO. I've...
Just to say, gapless rings are junk IMO. I've seen many have issues with them. Blowby being one of them. They can 'stick' together and not compress right and wear fast. I think they are more of a...
|
|
Forum: THE LOBBY
Yesterday, 08:33 AM
|
|
Replies: 3
Views: 245
R89 w/ topper
Saw this at a swap the other day, the guy cut the case top off, used a topper, and real caps, the topper caps are crappy. The eye is red too on the topper which looks bad. This battery he did...
|
|
Forum: Pontiac - Street
Yesterday, 08:23 AM
|
|
Replies: 13
Views: 289
|
|
Forum: THE LOBBY
Yesterday, 07:05 AM
|
|
Replies: 27
Views: 514
Could be Jack.
I think it was mainly all...
Could be Jack.
I think it was mainly all unincorporated area and it was just which town got the population?
As Hurry said, it is Clermont.
They were all mostly unpopulated, farm country...
|
|
Forum: OHC-6 TECH
Yesterday, 06:40 AM
|
|
Replies: 5
Views: 136
|
|
Forum: 66-67 GTO Tempest & LeMans TECH
Yesterday, 01:00 AM
|
|
Replies: 6
Views: 149
|
|
Forum: Pontiac - Street
06-11-2024, 11:03 PM
|
|
Replies: 28
Views: 689
I have to ask, did you use the same machinist...
I have to ask, did you use the same machinist each time you rebuilt the engine? Gapless rings are a little finicky I know I have used them in the past. They need a special finish to work correctly....
|
|
Forum: Pontiac - Street
06-11-2024, 10:25 PM
|
|
Replies: 28
Views: 689
When I had blowby , I think I took an old pcv...
When I had blowby , I think I took an old pcv valve and just cut out the middle (so valve was mostly open), this did not make much of a difference in the high rpm blowby. So, I generally just ran a...
|
