FAQ |
Members List |
Social Groups |
Calendar |
Search |
Today's Posts |
#161
|
||||
|
||||
It should read (So a guy changes the caps.) sorry
|
#162
|
||||
|
||||
1963 Interior trim pieces needed
Hi,
Looking for a decent interior center bottom windshield trim piece. This is the one that has the defrost vent openings. I'm assuming the one I need is for a glue in windshield and different from the rubber strip set windshield. I have one that does not match the contour or width of my corner trim(see photo). Also need upper trim piece for the drivers side rear 1/4 panel for a 2-door Lemans. This is the one with the 4 nails that hold the top of the panel in. Thanks,
__________________
Tom 1963 Lemans -428 +.030, SD Perf KRE heads, turbo 350, 9" Ford 3:90, 11.01@121 1956 Chieftain gasser, 461 stroked 400, SD Perf ported E-heads, turbo 400, Dana 3:70 10.40@125 |
#163
|
|||
|
|||
Carburetor?
Hello, any one have any leads on the rare Rochester 4BBL carb for the 4 CYL, the Carter AFB 9400 or what if any Holley would work with the 4BBL intake?
Thank you |
#164
|
|||
|
|||
Check with John from the carburetor shop.He can tell you what AFB could be setup to work with your intake.A Holley would take a adapter.Tom
|
#165
|
||||
|
||||
1963 lemans right front fender extention.
|
#166
|
||||
|
||||
I think I've got one off an Olds, if you don't mind it not being a perfect match to the original.
|
#167
|
||||
|
||||
I'll fix you up on this. Send a PM.
|
#168
|
||||
|
||||
PM sent
|
#169
|
||||
|
||||
|
#170
|
||||
|
||||
63 Interior trim
I need the upper trim piece for the drivers side rear interior 1/4 panel for a 2-door Lemans. This is the one with the 4 nails that hold the top of the panel in.
Also looking for a decent interior center bottom windshield trim piece or corner pieces that match my center. What I have does not match the contour or width of my corner trim(see photo). Thanks,
__________________
Tom 1963 Lemans -428 +.030, SD Perf KRE heads, turbo 350, 9" Ford 3:90, 11.01@121 1956 Chieftain gasser, 461 stroked 400, SD Perf ported E-heads, turbo 400, Dana 3:70 10.40@125 |
#171
|
||||
|
||||
your trim piece looks right, it just won't go in because its hitting the rubber or foam on the windshield.
__________________
63 Lemans ride along and drag race. https://www.youtube.com/watch?v=XMJHMPx7KAQ Gear Jamming https://www.youtube.com/watch?v=mw7KPRASomg At the track |
#172
|
||||
|
||||
That was actually before the new glass was installed. The only way I could have flattened the corners was to lay the trim front edge inside the channel which I'm sure wouldn't be right. Does anyone know if the trim had different contours if windshield was glued or rubber framed? I'm getting ready to modify the corners to match the center piece contour.
Thanks,
__________________
Tom 1963 Lemans -428 +.030, SD Perf KRE heads, turbo 350, 9" Ford 3:90, 11.01@121 1956 Chieftain gasser, 461 stroked 400, SD Perf ported E-heads, turbo 400, Dana 3:70 10.40@125 |
#173
|
||||
|
||||
Passenger Side Toe Kick Panel
Looking for a Passenger side toe kick panel for 1963 Lemans with AC. Preferably blue.
|
#174
|
||||
|
||||
4 bbl base
Looking for a 63 four barrel air cleaner base only. Thanks.
|
#175
|
|||
|
|||
Looking for a right front wheel cylinder for a 62 tempest. Thanks
|
#176
|
|||
|
|||
wheel cylinder
Quote:
If you don't come up with one you may want to check with White Post Restorations at this address: 1 Old Car Drive Post Office Box D White Post, VA 22663 (540) 837-1140 info@whitepost.com They can overhaul your piece and install a brass lining in it. (Never rusts) Good luck! |
#177
|
||||
|
||||
Interior trim piece
The last piece I need for my puzzle.
I need the upper stainless trim piece for the drivers side rear interior 1/4 panel for a 2-door Lemans. This is the one with the 4 nails that hold the top of the panel in. Thanks
__________________
Tom 1963 Lemans -428 +.030, SD Perf KRE heads, turbo 350, 9" Ford 3:90, 11.01@121 1956 Chieftain gasser, 461 stroked 400, SD Perf ported E-heads, turbo 400, Dana 3:70 10.40@125 |
#178
|
|||
|
|||
Looking for a fuel door with hinge. 1962 tempest
Thanks Sent from my VS990 using Tapatalk |
#179
|
||||
|
||||
Looking for the 2 pieces of chrome that covers the pinch welds for a 63 convertible. Can pick up at Norwalk. Call 603 477 7984
|
#180
|
||||
|
||||
Interior trim
Ok confirmed at Norwalk that I'm not frickin' crazy and do not have the correct center dash trim for my car. Looking for center dash trim that has a ducktail towards windshield consistent to all other 63s with a glue in windshield. See attached picture.
Also still need an upper trim for drivers side rear quarter interior panel. The part with the nail that secures the top of the panel. Thanks,
__________________
Tom 1963 Lemans -428 +.030, SD Perf KRE heads, turbo 350, 9" Ford 3:90, 11.01@121 1956 Chieftain gasser, 461 stroked 400, SD Perf ported E-heads, turbo 400, Dana 3:70 10.40@125 |
Reply |
|
|