Forum: THE LOBBY
09-21-2024, 09:03 AM
|
Replies: 146
Views: 12,053
|
Forum: THE LOBBY
09-20-2024, 08:10 AM
|
Replies: 146
Views: 12,053
|
Forum: THE LOBBY
09-19-2024, 06:32 PM
|
Replies: 12
Views: 742
Ford flathead 221 cubic inch V8.
This one is...
Ford flathead 221 cubic inch V8.
This one is from 1933 - 1937, 1932 had a one-barrel carb.
The water pumps were moved to the block from the heads for 1938 and later. Unfortunately with the...
|
Forum: Pontiac - Street
09-19-2024, 06:05 PM
|
Replies: 37
Views: 1,516
|
Forum: Pontiac - Street
09-19-2024, 12:35 AM
|
Replies: 37
Views: 1,516
350 guy here.
I've done a couple of...
350 guy here.
I've done a couple of iterations on 350 motors.
The first iteration was a very basic 69 350, #47 heads. This was the 1969 equivalent of your 1970 350. I put a Summit 2800 cam in...
|
Forum: Pontiac - Street
09-18-2024, 05:38 PM
|
Replies: 37
Views: 1,516
|
Forum: Pontiac - Street
09-18-2024, 02:32 PM
|
Replies: 37
Views: 1,516
As usual, late to a thread.
Your original...
As usual, late to a thread.
Your original request IS possible, however: I could NEVER have afforded the process without being able to trade out a bunch, and deduct more as advertising. You do not...
|
Forum: Pontiac - Street
09-18-2024, 02:04 PM
|
Replies: 37
Views: 1,516
|
Forum: Pontiac - Street
09-18-2024, 12:53 PM
|
Replies: 53
Views: 2,309
When I compared the 2802 cam specs, it is more...
When I compared the 2802 cam specs, it is more similar to a 744 cam. The HIT-284 Crane cam I pulled out was 228/235 at 050, about 500 lift. The stock retainers had mashed the aftermarket Viton...
|
Forum: Pontiac - Street
09-18-2024, 12:28 PM
|
Replies: 53
Views: 2,309
|
Forum: Pontiac - Street
09-18-2024, 11:43 AM
|
Replies: 53
Views: 2,309
|
Forum: Pontiac - Street
09-18-2024, 11:10 AM
|
Replies: 53
Views: 2,309
|
Forum: Pontiac - Street
09-18-2024, 11:05 AM
|
Replies: 53
Views: 2,309
|
Forum: Pontiac - Street
09-18-2024, 07:59 AM
|
Replies: 53
Views: 2,309
Good point in the above!
I forgot to mention...
Good point in the above!
I forgot to mention that 1.65 rockers can be dropped on any factory cam other then the RA4 cam without running into push rod to guide hole clearance issues, but once your...
|
Forum: Pontiac - Street
09-18-2024, 06:59 AM
|
Replies: 53
Views: 2,309
|
Forum: Pontiac - Street
09-18-2024, 06:52 AM
|
Replies: 53
Views: 2,309
|
Forum: Pontiac - Street
09-18-2024, 05:05 AM
|
Replies: 53
Views: 2,309
|
Forum: Pontiac - Street
09-18-2024, 04:58 AM
|
Replies: 53
Views: 2,309
You have not stated what was done to your #62...
You have not stated what was done to your #62 heads to allow them to work with the 488" exh valve lift of the 2802 Cam.
Even if you have changed valve springs to allow the use of 1.65 rockers...
|
Forum: Pontiac - Street
09-18-2024, 01:45 AM
|
Replies: 53
Views: 2,309
|
Forum: Pontiac - Street
09-18-2024, 12:54 AM
|
Replies: 53
Views: 2,309
|
Forum: Pontiac - Street
09-18-2024, 12:25 AM
|
Replies: 53
Views: 2,309
I agree that it seems unlikely that it's the...
I agree that it seems unlikely that it's the exhaust alone. My stock RAIII ran as you'd expect it to with a basic factory style Gardner exhaust system. Your engine combo seems a bit better than a...
|
Forum: Pontiac - Street
09-18-2024, 12:01 AM
|
Replies: 53
Views: 2,309
|
Forum: Pontiac - Street
09-17-2024, 11:31 PM
|
Replies: 53
Views: 2,309
|
Forum: Pontiac - Street
09-17-2024, 10:33 PM
|
Replies: 53
Views: 2,309
I've got the same engine, 400, 62 heads, 2802...
I've got the same engine, 400, 62 heads, 2802 cam, 1.5 rockers. RPM intake, QF 750 double pumper, headers, 2.5 exhaust, magnaflow mufflers dumped. 35* at 3000. Loose converter and 3.25 gears with...
|
Forum: Pontiac - Street
09-17-2024, 08:06 PM
|
Replies: 53
Views: 2,309
No disrespect intended, but that Gardner style...
No disrespect intended, but that Gardner style exhaust could be a choke point. I know I had one and loved the sound, but taking mine off got me probably 30 hp. I had a 66 GTO that i dynoed on a...
|